u-boot.git/arch/arm/cpu/pxa, branch master

arm: Remove PXA architecture support

2022-07-07T13:29:08+00:00

With the last platform for this architecture removed, remove the rest of
the architecture support as well.

Cc: Marek Vasut 
Signed-off-by: Tom Rini 
Reviewed-by: Simon Glass

arm: pxa: Remove CONFIG_CPU_PXA25X

2022-06-06T16:09:12+00:00

There are no platforms that set this, remove the code.

Signed-off-by: Tom Rini

Convert CONFIG_SKIP_LOWLEVEL_INIT et al to Kconfig

2021-08-31T21:47:49+00:00

This converts the following to Kconfig:
   CONFIG_SKIP_LOWLEVEL_INIT
   CONFIG_SKIP_LOWLEVEL_INIT_ONLY

In order to do this, we need to introduce SPL and TPL variants of these
options so that we can clearly disable these options only in SPL in some
cases, and both instances in other cases.

Signed-off-by: Tom Rini

reset: Remove addr parameter from reset_cpu()

2021-03-02T19:03:02+00:00

Historically, the reset_cpu() function had an `addr` parameter which was
meant to pass in an address of the reset vector location, where the CPU
should reset to.  This feature is no longer used anywhere in U-Boot as
all reset_cpu() implementations now ignore the passed value.  Generic
code has been added which always calls reset_cpu() with `0` which means
this feature can no longer be used easily anyway.

Over time, many implementations seem to have "misunderstood" the
existence of this parameter as a way to customize/parameterize the reset
(e.g.  COLD vs WARM resets).  As this is not properly supported, the
code will almost always not do what it is intended to (because all
call-sites just call reset_cpu() with 0).

To avoid confusion and to clean up the codebase from unused left-overs
of the past, remove the `addr` parameter entirely.  Code which intends
to support different kinds of resets should be rewritten as a sysreset
driver instead.

This transformation was done with the following coccinelle patch:

    @@
    expression argvalue;
    @@
    - reset_cpu(argvalue)
    + reset_cpu()

    @@
    identifier argname;
    type argtype;
    @@
    - reset_cpu(argtype argname)
    + reset_cpu(void)
    { ... }

Signed-off-by: Harald Seiler 
Reviewed-by: Simon Glass

common: Drop linux/delay.h from common header

2020-05-19T01:19:23+00:00

Move this uncommon header out of the common header.

Signed-off-by: Simon Glass

common: Drop init.h from common header

2020-05-18T21:33:33+00:00

Move this uncommon header out of the common header.

Signed-off-by: Simon Glass

common: Drop net.h from common header

2020-05-18T21:33:31+00:00

Move this header out of the common header. Network support is used in
quite a few places but it still does not warrant blanket inclusion.

Note that this net.h header itself has quite a lot in it. It could be
split into the driver-mode support, functions, structures, checksumming,
etc.

Signed-off-by: Simon Glass

common: Move enable/disable_interrupts out of common.h

2019-12-02T23:25:01+00:00

Move these two functions into the irq_funcs.h header file. Also move
interrupt_handler_t as this is used by the irq_install_handler() function.

Signed-off-by: Simon Glass 
Reviewed-by: Tom Rini

common: Move ARM cache operations out of common.h

2019-12-02T23:24:58+00:00

These functions are CPU-related and do not use driver model. Move them to
cpu_func.h

Signed-off-by: Simon Glass 
Reviewed-by: Daniel Schwierzeck 
Reviewed-by: Tom Rini

common: Move some cache and MMU functions out of common.h

2019-12-02T23:23:55+00:00

These functions belong in cpu_func.h. Another option would be cache.h
but that code uses driver model and we have not moved these cache
functions to use driver model. Since they are CPU-related it seems
reasonable to put them here.

Move them over.

Signed-off-by: Simon Glass 
Reviewed-by: Tom Rini