u-boot.git/arch/arm/dts/sun7i-a20-pcduino3.dts, branch master

sunxi: dts: arm: update devicetree files

2022-10-18T07:18:22+00:00

Update the devicetree files from the Linux kernel, version v6.0-rc4.
This is covering the 32-bit SoCs, from arch/arm/boot/dts/.

This avoids the not backwards-compatible r_intc binding change, to allow
older kernels to boot, but the other nodes are updated.

Not much change here, the vast majority is actually cosmetic: node names
and using symbolic names for the the RTC clocks.
The R40 boards gain DVFS support.
Some A23/A33 tablet DTs are unified into a single file.

Signed-off-by: Andre Przywara 
Reviewed-by: Jernej Skrabec

ARM: dts: sun7i: Sync from Linux v5.18-rc1

2022-05-22T23:37:50+00:00

Copy the devicetree source for the A20 SoC and all existing boards
verbatim from the Linux v5.18-rc1 tag.

This commit also adds the following new board devicetrees:
 - sun7i-a20-haoyu-marsboard.dts
 - sun7i-a20-linutronix-testbox-v2.dts
 - sun7i-a20-olinuxino-lime-emmc.dts

This update includes changes to the USB PHY detection GPIO properties
which are needed to convert that driver to use the DM GPIO framework.

Signed-off-by: Samuel Holland 
[Andre: fix Mele M5 U-Boot only DT]
Reviewed-by: Andre Przywara 
Signed-off-by: Andre Przywara

arm: allwinner: dts: a20: Sync A20 dts(i) files from Linux 5.1-rc2

2019-04-17T09:04:45+00:00

Sync sun7i-a20 dts(i) files from Linux 5.1-rc2

Linux commit details about the sun7i-a20* sync:
"ARM: dts: sun7i: bananapi: Add GPIO banks regulators"
(sha1: 09c6572290f018d73ec2e812e28bada34d41815f)

Here are U-Boot specific dts changes.

- s/uart0_pins_a/uart0_pb_pins for
  sun7i-a20-ainol-aw1.dts
  sun7i-a20-m5.dts
  sun7i-a20-primo73.dts
  sun7i-a20-yones-toptech-bd1078.dts
  sunxi-itead-core-common.dtsi
- s/gmac_pins_mii_a/gmac_rgmii_pins for
  sun7i-a20-m5.dts
- drop i2c0, i2c1 pins from
  sunxi-itead-core-common.dtsi
- drop mmc0 pins from
  sun7i-a20-primo73.dts

Signed-off-by: Jagan Teki

ARM: dts: sun7i: Update A20 dts(i) files from Linux-v4.18-rc3

2018-09-28T16:39:24+00:00

Update all A10 devicetree dtsi and dtsi files from Linux-v4.18-rc3
with below commit:
commit 5d9ef839f874f4e3923c8a9ae7b136c6c3912cd5
Author: Stefan Mavrodiev 
Date:   Wed May 16 14:38:08 2018 +0300

    ARM: dts: sun7i: Add Olimex A20-SOM-EVB-eMMC board

Note:
- Update sun7i-a20-primo73.dts as per Linux, since
  this dts is U-Boot specific.
- Drop sun7i-a20-olimex-som-evb-emmc.dts since no board
  added for this.

Signed-off-by: Jagan Teki

ARM: sunxi: Remove left-over cd-inverted property from pcDuino3

2018-01-10T06:07:09+00:00

Commit 8620f384098b ("dm: sunxi: Linksprite_pcDuino3: Correct polarity
of MMC card detect") claims that the Pcduino3 device tree had an
incorrect polarity for the card detect pin and thus changed the polarity
flag of the cd-gpios from GPIO_ACTIVE_HIGH to GPIO_ACTIVE_LOW.

Actually the DT was correct since according to the mmc binding, a
combination of GPIO_ACTIVE_HIGH + cd-inverted results in an active-low
polarity. But because the U-Boot driver lacks the code to look at the
cd-inverted property (unlike the Linux driver) it interpreted the
polarity of active-high. Thus, after that commit the DT is actually
wrong from the binding/Linux point of view.

To make both Linux and U-Boot interpret the DT in the same way, just
drop the left-over cd-inverted property. I've sent a Linux patch to
switch all sunxi DTs over to not using the cd-inverted property, so
eventually all sunxi boards in U-Boot will be consistent in not using
cd-inverted.

Signed-off-by: Tuomas Tynkkynen 
Acked-by: Maxime Ripard 
Reviewed-by: Jagan Teki

dm: sunxi: Linksprite_pcDuino3: Correct polarity of MMC card detect

2017-08-01T02:58:01+00:00

This is shown as active high in the schematics[1], so fix it.

[1] https://patchwork.ozlabs.org/patch/777890/

Signed-off-by: Simon Glass 
Reported-by: Maxime Ripard

sunxi: Sync dts files with the upstream kernel

2016-03-23T21:04:13+00:00

Sync dts files with the upstream kernel including
changes queued for 4.6:

https://git.kernel.org/cgit/linux/kernel/git/mripard/linux.git/commit/?h=sunxi/dt-for-4.6

Note this adds a number of new unused board dts files. I've asked the
authors of the kernel commits adding these to submit a matching defconfig
to u-boot.

Signed-off-by: Hans de Goede 
Acked-by: Ian Campbell

sunxi: Sync dts files with the linux kernel

2015-06-04T12:12:03+00:00

Copy over all the latest dts changes from mripard/sunxi/dt-for-4.2 ,
this gives us a proper dtsi file for the A33 rather then abusing
sun8i-a23.dtsi for this.

And this replaces our minimal (dummy) sun7i-a20-mk808c and
sun8i-a33-astar-mid756 dts files with proper ones.

Signed-off-by: Hans de Goede 
Acked-by: Ian Campbell

sunxi: dts: Sync all dts files with upstream kernel

2015-05-04T14:51:54+00:00

Bring all the sunxi dts files (and update existing ones) from
mripard/sunxi/dt-for-4.1 (which will be merged into upstream master any
day now). This is necessary so that we can move all sunxi boards over to
the driver model.

Signed-off-by: Hans de Goede 
Reviewed-by: Simon Glass 
Acked-by: Ian Campbell

dm: sunxi: Add support for serial using driver model

2014-11-05T12:09:58+00:00

Add a driver for the designware serial UART used on sunxi. This just
redirects to the normal ns16550 driver.

Add a stdout-path to the device tree so that the correct UART is chosen.

Signed-off-by: Simon Glass 
Signed-off-by: Hans de Goede