u-boot.git/arch/arm/include/asm/arch-mx6, branch v2012.04

imx: Remove unneeded/repititive definitions from imx headers

2012-04-16T12:53:59Z

Remove gpio related unused/repititive definitions from imx headers. Signed-off-by: Vikram Narayanan Acked-by: Stefano Babic

i.MX6: define CACHELINE_SIZE

2012-04-16T12:53:58Z

Signed-off-by: Eric Nelson Acked-by: Marek Vasut

mx6: Read silicon revision from register

2012-03-27T07:41:16Z

Instead of hardcoding the mx6 silicon revision, read it in run-time. Also, besides the silicon version print the mx6 variant type: quad,dual/solo or solo-lite. Tested on a mx6qsabrelite, where it shows: CPU: Freescale i.MX6Q rev1.0 at 792 MHz Signed-off-by: Fabio Estevam Acked-by: Stefano Babic Acked-by: Jason Liu

mx6: Remove duplicate definition of ANATOP_BASE_ADDR

2012-03-27T07:41:16Z

Remove duplicate definition of ANATOP_BASE_ADDR. Signed-off-by: Fabio Estevam

usb/ehci: Add USB support for the MX6Q

2012-03-26T21:09:23Z

Currently, only USB Host 1 is supported. Cc: Remy Bohmer Signed-off-by: Wolfgang Grandegger

net: fec_mxc: add 1000 Mbps selection

2012-02-27T20:19:24Z

Define FEC_QUIRK_ENET_MAC and add to arch-mx6/imx-regs.h Signed-off-by: Troy Kisky Acked-by: Dirk Behme

mx6q: Add support for ECSPI through mxc_spi driver

2012-02-27T20:19:23Z

Signed-off-by: Eric Nelson Acked-by: Dirk Behme Acked-by: Stefano Babic Acked-by: Jason Liu

mx6q: define GPIO macros for translating between ordinals and port:index

2012-02-27T20:19:23Z

The interface to the mxc_gpio driver uses integer (ordinal) values to refer to all GPIOs on the i.MX processors. The registers themselves and much of the i.MX documentation are banked in groups of 32, and these macros allow the use of the port:index numbering for clarity. GPIO_NUMBER() converts to ordinal value from port:index GPIO_PORT() returns the port of an ordinal value GPIO_INDEX() returns the index or offset of the ordinal. Discussion on the mailing list at http://lists.denx.de/pipermail/u-boot/2012-January/116927.html Signed-off-by: Eric Nelson Signed-off-by: Eric Nelson

i.mx6: mx6x_pins: Fix uart txd definitions

2012-02-12T09:11:26Z

The uart txd pad can also provide the rxd function. But it does not stop its tx role. This could be used for a half duplex serial port. Change names to reduce confusion. Signed-off-by: Troy Kisky CC: Troy Kisky CC: Jason Liu CC: Stefano Babic Acked-by: Jason Liu

imx: mx6q: add aipstz init for off platform periph

2012-01-16T07:40:10Z

Init peripheral access control register of AIPSTZ OPACRx: Buffer Writes(BW): 0 -> not bufferable, Supervisor Protect(SP): 0 -> not require supervisor privilege level for accesses. Write Protect(WP): 0 -> allows write accesses. Trusted Protect(TP): 0 -> allows unstrusted master Signed-off-by: Jason Liu Cc: Stefano Babic