u-boot.git/arch/arm/include/asm/imx-common, branch v2016.11

arm: imx: Add Engicam i.CoreM6 QDL Starter Kit initial support

2016-10-26T14:53:16Z

Boot Log for i.CoreM6 DualLite/Solo Starter Kit: ----------------------------------------------- U-Boot SPL 2016.09-rc2-30739-gd1fa290 (Sep 17 2016 - 00:37:46) Trying to boot from MMC1 U-Boot 2016.09-rc2-30739-gd1fa290 (Sep 17 2016 - 00:37:46 +0530) CPU: Freescale i.MX6SOLO rev1.3 at 792MHz CPU: Industrial temperature grade (-40C to 105C) at 31C Reset cause: POR DRAM: 256 MiB MMC: FSL_SDHC: 0 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: CPU Net Initialization Failed No ethernet found. Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc0 is current device switch to partitions #0, OK mmc0 is current device reading boot.scr ** Unable to read file boot.scr ** reading zImage 6741808 bytes read in 341 ms (18.9 MiB/s) Booting from mmc ... reading imx6dl-icore.dtb 30600 bytes read in 19 ms (1.5 MiB/s) Booting using the fdt blob at 0x18000000 Using Device Tree in place at 18000000, end 1800a787 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 Boot Log for i.CoreM6 Quad/Dual Starter Kit: -------------------------------------------- U-Boot SPL 2016.09-rc2-30739-gd1fa290 (Sep 17 2016 - 00:37:46) Trying to boot from MMC1 U-Boot 2016.09-rc2-30739-gd1fa290 (Sep 17 2016 - 00:37:46 +0530) CPU: Freescale i.MX6Q rev1.2 at 792MHz CPU: Industrial temperature grade (-40C to 105C) at 28C Reset cause: POR DRAM: 512 MiB MMC: FSL_SDHC: 0 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: CPU Net Initialization Failed No ethernet found. Hit any key to stop autoboot: 0 icorem6qdl> Cc: Stefano Babic Cc: Fabio Estevam Cc: Matteo Lisi Cc: Michael Trimarchi Acked-by: Peng Fan Signed-off-by: Jagan Teki

imx-common: enlarge mux width to 4

2016-10-04T17:37:28Z

For i.MX6, the mux width is 4, not 3. So enlarge the width. IOMUX_CONFIG_LPSR is changed from 0x8 to 0x20 to not use bit 3 of mux. Signed-off-by: Peng Fan Cc: Stefano Babic

imx: iomux: fix snvs usage for i.MX6ULL

2016-10-04T13:41:01Z

SNVS TAMPER pin and BOOT MODE pins are in SNVS IOMUXC module, not in IOMUXC, so correct the related registers' offset. Use IOMUX_CONFIG_LPSR flag for these pins, so we can differentiate them from iomuxc pins. Signed-off-by: Peng Fan Cc: Stefano Babic Cc: "Benoît Thébaudeau"

imx-common: introduce is_mx6ull

2016-10-04T13:41:00Z

Introduce is_mx6ull macro. Signed-off-by: Peng Fan Cc: Stefano Babic

imx-common: introduce simpler macros for runtime dection

2016-05-24T12:59:55Z

Introduce simpler macros for runtime cpu dection. Signed-off-by: Peng Fan Cc: Stefano Babic Acked-by: Stefano Babic

dm: i2c: mxc_i2c: implement i2c_idle_bus

2016-03-28T07:22:58Z

Implement i2c_idle_bus in driver, then setup_i2c can be dropped for boards which enable DM_I2C/DM_GPIO/PINCTRL. The i2c_idle_bus force bus idle flow follows setup_i2c in arch/arm/imx-common/i2c-mxv7.c This patch is an implementation following linux kernel patch: " commit 1c4b6c3bcf30d0804db0d0647d8ebeb862c6f7e5 Author: Gao Pan Date: Fri Oct 23 20:28:54 2015 +0800 i2c: imx: implement bus recovery Implement bus recovery methods for i2c-imx so we can recover from situations where SCL/SDA are stuck low. Once i2c bus SCL/SDA are stuck low during transfer, config the i2c pinctrl to gpio mode by calling pinctrl sleep set function, and then use GPIO to emulate the i2c protocol to send nine dummy clock to recover i2c device. After recovery, set i2c pinctrl to default group setting. " See Documentation/devicetree/bindings/i2c/i2c-imx.txt for detailed description. 1. Introuduce scl_gpio/sda_gpio/bus in mxc_i2c_bus. 2. Discard the __weak attribute for i2c_idle_bus and implement it, since we have pinctrl driver/driver model gpio driver. We can use device tree, but not let board code to do this. 3. gpio state for mxc_i2c is not a must, but it is recommended. If there is no gpio state, driver will give tips, but not fail. 4. The i2c controller was first probed, default pinctrl state will be used, so when need to use gpio function, need to do "pinctrl_select_state(dev, "gpio")" and after force bus idle, need to switch back "pinctrl_select_state(dev, "default")". This is example about how to use the gpio force bus idle function: " &i2c1 { clock-frequency = <100000>; pinctrl-names = "default", "gpio"; pinctrl-0 = <&pinctrl_i2c1>; pinctrl-1 = <&pinctrl_i2c1_gpio>; scl-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>; sda-gpios = <&gpio1 29 GPIO_ACTIVE_HIGH>; status = "okay"; [....] }; [.....] pinctrl_i2c1_gpio: i2c1grp_gpio { fsl,pins = < MX6UL_PAD_UART4_TX_DATA__GPIO1_IO28 0x1b8b0 MX6UL_PAD_UART4_RX_DATA__GPIO1_IO29 0x1b8b0 >; }; " Signed-off-by: Peng Fan Cc: Albert Aribaud Cc: Stefano Babic Cc: Heiko Schocher Cc: Simon Glass Cc: York Sun

imx: imx-common: introduce Resource Domain Controller support

2016-02-21T10:46:26Z

Introduce Resource Domain Controller support for i.MX. Now i.MX6SX and i.MX7D supports this feature to assign masters and peripherals to different domains. Signed-off-by: Ye.Li Signed-off-by: Peng Fan

imx: nand: update GPMI NAND driver to support MX7

2016-01-24T11:09:32Z

Update GPMI NAND driver and BCH head file to support i.MX7 Signed-off-by: Peng Fan Cc: Stefano Babic

imx: apbh_dma: Update APBH-DMA for MX7D

2016-01-24T11:09:16Z

Update APBH-DMA driver and head files to support i.MX7D Signed-off-by: Peng Fan Cc: Stefano Babic

iomux-v3: Take MX6D in consideration for imx_iomux_v3_setup_pad()

2015-11-25T08:41:29Z

We should also take MX6D option in consideration when defining imx_iomux_v3_setup_pad(). Signed-off-by: Otavio Salvador Reviewed-by: Fabio Estevam