u-boot.git/arch/arm/include/asm, branch v2012.07

mx6: Make pad name macro consistent with the datasheet

2012-07-20T21:03:28+00:00

Use the same name as defined in the datasheet.
DSP_CLK -> DISP_CLK

Signed-off-by: Ashok Kumar Reddy Kourla 
Acked-by: Marek Vasut

Merge branch 'next' of git://git.denx.de/u-boot-video

2012-07-18T08:47:03+00:00

* 'next' of git://git.denx.de/u-boot-video:
  ipu_common: Add ldb_clk for use in parenting the pixel clock
  ipu_common: Do not hardcode the ipu_clk frequency
  ipu_common: Rename MXC_CCM_BASE
  ipu_common: Let clk_ipu_enable/disable only run on MX51 and MX53
  ipu_common: Only apply the erratum to MX51
  video: Rename CONFIG_VIDEO_MX5
  mx6: Allow mx6 to access the IPUv3 registers
  common lcd: minor coding style changes

Signed-off-by: Wolfgang Denk

mxc_i2c: specify i2c base address in config file

2012-07-11T08:54:29+00:00

The following platforms had their config files changed
flea3, imx31_phycore, mx35pdk, mx53ard, mx53evk, mx53smd
and mx53loco.

Signed-off-by: Troy Kisky 
Acked-by: Stefano Babic

mx6: Allow mx6 to access the IPUv3 registers

2012-07-10T09:35:38+00:00

Adjust the IPUv3 registers, so that the IPUv3 driver can be extended for mx6 as well.

Signed-off-by: Fabio Estevam

Merge branch 'master' of git://git.denx.de/u-boot-arm

2012-07-10T06:54:41+00:00

* 'master' of git://git.denx.de/u-boot-arm:
  tegra: define fdt_load/fdt_high variables
  tegra: enable bootz command
  tegra: usb: Fix device enumeration problem of USB1
  tegra: trimslice: set up serial flash pinmux
  tegra: add pin_mux_spi() board initialization function
  tegra: add GMC/GMD funcmux entry for SFLASH
  tegra: bootcmd: start USB only when needed
  tegra: bootcmd enhancements
  tegra: add enterrcm command
  tegra: enable CONFIG_ENV_VARS_UBOOT_CONFIG
  Add env vars describing U-Boot target board
  tegra: usb: fix wrong error check
  tegra: add ULPI on USB2 funcmux entry
  tegra: fix leftover CONFIG_TEGRA2_MMC & _SPI build switches
  tegra: Add Tamonten Evaluation Carrier support
  tegra: Use SD write-protect GPIO on Tamonten
  tegra: Implement gpio_early_init() on Tamonten
  tegra: Allow boards to perform early GPIO setup
  tegra: plutux: Add device tree support
  tegra: medcom: Add device tree support
  tegra: Rework Tamonten support
  beagle: add eeprom expansion board info for bct brettl4

Signed-off-by: Wolfgang Denk

tegra: usb: Fix device enumeration problem of USB1

2012-07-09T20:44:34+00:00

A known hardware issue of USB1 port where bit 1 (connect status
change) of PORTSC register will be set after issuing Port Reset
(like "usb reset" in u-boot command line).
This will be treated as an error and stops later device enumeration.

Therefore we clear that bit after Port Reset in order to proceed
later device enumeration.

Signed-off-by: Jim Lin 
Acked-by: Stephen Warren 
Signed-off-by: Tom Warren

tegra: add GMC/GMD funcmux entry for SFLASH

2012-07-09T20:44:33+00:00

This is used on TrimSlice.

Signed-off-by: Stephen Warren 
Signed-off-by: Tom Warren

tegra: add ULPI on USB2 funcmux entry

2012-07-09T20:44:33+00:00

This is needed as a prerequisite for Tegra USB ULPI support
within U-Boot.

Signed-off-by: Lucas Stach 
Acked-by: Stephen Warren 
CC: Stephen Warren 
CC: Tom Warren 
Signed-off-by: Tom Warren

EXYNOS5: USB: Fix incorrect USB base addresses

2012-07-09T16:27:55+00:00

This patch corrects the base addresses for USB_PHY and USB_OTG.

Signed-off-by: Vivek Gautam 
Signed-off-by: Rajeshwari Shinde 
Acked-by: Chander Kashyap 
Acked-by: Minkyu Kang

EXYNOS: Add power Enable/Disable for USB-EHCI

2012-07-09T16:27:55+00:00

This patch adds functions to enable/disable the power of USB
host controller for EXYNOS5.

Signed-off-by: Vivek Gautam 
Signed-off-by: Che-Liang Chiou 
Signed-off-by: Rajeshwari Shinde