u-boot.git/arch/arm/include/asm, branch v2020.07

ARM: imx: ddr: Fill in missing DDRC ZQCTLx on i.MX7

2020-06-22T15:44:06Z

The iMX7 defines further DDRC ZQCTLx registers, however those were thus far missing from the list of registers and not programmed. On systems with LPDDR2 or DDR3, those registers must be programmed with correct values, otherwise the DRAM may not work. However, existing systems which worked without programming these registers before are now setting those registers to 0, which is the default value, so no functional change there. Signed-off-by: Marek Vasut Cc: Fabio Estevam Cc: NXP i.MX U-Boot Team Cc: Peng Fan Cc: Stefano Babic

ARM: imx: ddr: Add missing PHY reset

2020-06-08T08:42:54Z

The iMX7D RM 9.2.4.9.3 Power removal flow Table 9-11. Re-enabling power explicitly says both the DDR controller and the PHY must be reset in the correct sequence. Currently the code only resets the controller. This leads to a misbehavior where the system brings the DRAM up after reboot, but the DRAM is unstable. Add the missing reset. The easiest way to trigger this is by triggering WDT without having the WDT assert WDOG_B signal, i.e. mw.w 0x30280000 0x25 . Signed-off-by: Marek Vasut Cc: Fabio Estevam Cc: NXP i.MX U-Boot Team Cc: Peng Fan Cc: Stefano Babic

Merge tag 'efi-2020-07-rc4' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi

2020-06-03T18:10:03Z

Pull request for UEFI sub-system for efi-2020-07-rc4 This patch series addresses the following issues: * allow compiling with clang * add missing function descriptions to the HTML documentation * simplify the validation of UEFI images * validate load options in the UEFI boot manager In a preparatory patch a structure definition is moved.

efi_loader: allow compiling with clang

2020-06-03T15:19:17Z

On ARM systems gd is stored in register r9 or x18. When compiling with clang gd is defined as a macro calling function gd_ptr(). So we can not make assignments to gd. In the UEFI sub-system we need to save gd when leaving to UEFI binaries and have to restore gd when reentering U-Boot. Define a new function set_gd() for setting gd and use it in the UEFI sub-system. Signed-off-by: Heinrich Schuchardt Tested-by: Tom Rini

ARM: add psci_arch_init() declaration for CONFIG_ARMV7_PSCI

2020-06-02T21:27:04Z

arch/arm/include/asm/system.h declares psci_arch_init(), but it is surrounded by #ifdef CONFIG_ARMV8_PSCI. psci_arch_init() is called for CONFIG_ARMV7_PSCI too. Add the missing function declaration. Signed-off-by: Masahiro Yamada

usb: ehci-omap: Add Support for DM_USB and OF_CONTROL

2020-05-22T13:22:35Z

The omap3.dtsi file shows the usbhshost node with two sub-nodes for ohci and ehci. This patch file creates the usbhshost, and pulls the portX-mode information. It then locates the EHCI sub-node, and initializes the EHCI controller with the info pulled from the usbhshost node. There is still more to do since there isn't an actual link between the 'phys' reference and the corresponding phy driver, and there is no nop-xceiv driver yet. In the meantime, the older style reference to CONFIG_OMAP_EHCI_PHYx_RESET_GPIO is still needed to pull the phy out of reset until the phy driver is completed and the phandle reference is made. Signed-off-by: Adam Ford

Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriq

2020-05-20T12:46:56Z

- Add DM_ETH support for lx2160aqds, ls2080aqds, ls1088aqds - QSI related fixes on ls1012a, ls2080a, ls1046a, ls1088a, ls1043a based platforms - Bug-fixes/updtaes related to ls1046afrwy, fsl-mc, msi-map property

treewide: Remove unused FSL QSPI config options for Layerscape platforms

2020-05-19T03:52:05Z

Some of these options are not used by the driver anymore and some of them are obsolete as the information is gathered from the dt. Also consolidating defines in common headers. Signed-off-by: Frieder Schrempf Signed-off-by: Ashish Kumar Signed-off-by: Kuldeep Singh Reviewed-by: Priyanka Jain

common: Drop linux/bitops.h from common header

2020-05-19T01:19:23Z

Move this uncommon header out of the common header. Signed-off-by: Simon Glass

Use ASSEMBLY as the assembly macros