Drop override of dram_init_banksize() weak function for mt8516. This is
effectively the same as the default implementation, so we do not need
to override it.

Reviewed-by: Julien Stephan <jstephan@baylibre.com>
Tested-by: Julien Stephan <jstephan@baylibre.com>
Link: https://patch.msgid.link/20260319-mtk-init-fix-dram-v1-15-6171ec141f40@baylibre.com
Signed-off-by: David Lechner <dlechner@baylibre.com>

Consolidate all mem_map definitions for MediaTek ARMv8 platforms into a
single file. The size of the DDR and MMIO regions can vary, so Kconfig
options are added to configure them by target.

Signed-off-by: David Lechner <dlechner@baylibre.com>

Make the mtk_pll_early_init() function static in several files. It is
only used within those files, so there is no need to have it in the
global namespace.

Reviewed-by: Macpaul Lin <macpaul.lin@mediatek.com>

As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.

Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>

When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.

This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.

Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>

Remove <common.h> from all mach-mediatek files and when needed add
missing include files directly.

Signed-off-by: Tom Rini <trini@konsulko.com>

Historically, the reset_cpu() function had an `addr` parameter which was
meant to pass in an address of the reset vector location, where the CPU
should reset to.  This feature is no longer used anywhere in U-Boot as
all reset_cpu() implementations now ignore the passed value.  Generic
code has been added which always calls reset_cpu() with `0` which means
this feature can no longer be used easily anyway.

Over time, many implementations seem to have "misunderstood" the
existence of this parameter as a way to customize/parameterize the reset
(e.g.  COLD vs WARM resets).  As this is not properly supported, the
code will almost always not do what it is intended to (because all
call-sites just call reset_cpu() with 0).

To avoid confusion and to clean up the codebase from unused left-overs
of the past, remove the `addr` parameter entirely.  Code which intends
to support different kinds of resets should be rewritten as a sysreset
driver instead.

This transformation was done with the following coccinelle patch:

    @@
    expression argvalue;
    @@
    - reset_cpu(argvalue)
    + reset_cpu()

    @@
    identifier argname;
    type argtype;
    @@
    - reset_cpu(argtype argname)
    + reset_cpu(void)
    { ... }

Signed-off-by: Harald Seiler <hws@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>

Move this out of the common header and include it only where needed.  In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly.   Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>

In the spirit of using the same base name for all of these related macros,
rename this to have the operation at the end. This is not widely used so
the impact is fairly small.

Signed-off-by: Simon Glass <sjg@chromium.org>

Move this uncommon header out of the common header.

Signed-off-by: Simon Glass <sjg@chromium.org>