Some Qualcomm boards feature reserved ranges of pins which are protected
by firmware. Attempting to read or write any registers associated with
these pins results the board resetting.

Add support for parsing these ranges from devicetree and ensure that the
pinctrl and GPIO drivers don't try to interact with these pins.

Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250410-topic-sm8x50-pinctrl-reserved-ranges-v2-1-654488392b9a@linaro.org
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>

In order to help setup pin configuration for special pins (UFS, SDCard),
introduce the msm_special_pin_data struct largely inspired from the
Linux conterpart but with only U-Boot required fields.

This struct is added to the pins_data to allow specifying the special
pins data for each SoC.

Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>

Some of the db410c board support code was written to be generic and
placed in mach-snapdragon. However, as the db410c is the only board
using this, move the code out of mach-snapdragon. This makes is more
obvious what code is relevant for which targets and helps tidy things up
a little more.

Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org> #qcs404
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>

Most platforms have a handful of "special" GPIOs, like the MMC
clock/data lanes, UFS reset, etc. These don't follow the usual naming
scheme of "gpioX" and also have unique capabilities and registers. We
can get away without supporting them all for now, but DT compatibility
is still an issue.

Add support for allowing these to be specified after the other pins, and
make all pinmux/pinconf calls for them nop.

Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org> #qcs404
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>

The pinctrl and GPIO drivers are currently heavily incompatible with
upstream. Most Qualcomm pinctrl blocks feature "tiles" of pins, each at
it's own address. Introduce support for these by allowing the soc driver
to specify per-pin register offsets similarly to the Linux driver.

Adjust the GPIO driver to handle these too, and finally enable support
for all pins with the same numbering as used in Linux.

Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>

Currently, it isn't possible to build clock drivers for more than one
platform due to how the msm_enable() and msm_set_rate() callbacks are
implemented.

Extend qcom_clk_data to include function pointers for these and convert
all platforms to use them.

Previously, clock drivers relied on include/configs/<board.h> to include the
board specific sysmap header, however as most of the header contents are clock
driver related, import the contents directly into each clock driver and
remove the header. The only exception here is the dragonboard820c board file
which includes some pinctrl macros, those are also inlined.

Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
[caleb: remove additional sysmap-sdm845.h mention]

Co-developed-by: Mike Worsfold <mworsfold@impinj.com>
Signed-off-by: Mike Worsfold <mworsfold@impinj.com>
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>

Signed-off-by: Sumit Garg <sumit.garg@linaro.org>

Add support for USB controller and PHY clocks for QCS404 SoC.

Signed-off-by: Sumit Garg <sumit.garg@linaro.org>

Currently this clock driver initializes clocks for UART and eMMC. Along
with this import "qcom,gcc-qcs404.h" header from Linux mainline to
support DT bindings.

Signed-off-by: Sumit Garg <sumit.garg@linaro.org>