Added extended support for retrieving the PMC muti boot mode
register via the firmware interface, which is preferred when
U-Boot runs in EL2 and cannot directly access PMC registers
via raw reads. Ideally, all secure registers should be accessed
via xilinx_pm_request(). Introduced the secure
zynqmp_pm_get_pmc_multi_boot_reg() call, which uses
xilinx_pm_request() to read the PMC multi boot mode register.

BootROM increments the MultiBoot register (PMC_MULTI_BOOT) read
address offset by 32 KB and retries. For SD and eMMC boot modes,
it can search up to 8191 FAT files for the identification string.
A 13-bit mask (0x1FFF) is applied to PMC_MULTI_BOOT_MASK to obtain
the correct values in BootROM.

Signed-off-by: Prasad Kummari <prasad.kummari@amd.com>
Link: https://lore.kernel.org/r/20250305134845.3182193-1-prasad.kummari@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>

Turn anonymous enum TCM_LOCK/TCM_SPLIT into enum tcm_mode {}, set
TCM_LOCK as 0 and TCM_SPLIT as 1 to match LOCK and SPLIT macros in
mach-zynqmp/mp.c, and unify all the functions and their parameters
on this one single enum tcm_mode {} instead of a mix of bool and u8.
No functional change intended.

Signed-off-by: Marek Vasut <marex@denx.de>
Tested-by: Love Kumar <love.kumar@amd.com>
Link: https://lore.kernel.org/r/20250206213039.42756-1-marex@denx.de
Signed-off-by: Michal Simek <michal.simek@amd.com>

The SelectMAP configuration interface provides an 8-bit,
16-bit or 32-bit bidirectional data bus interface to the Versal FPGA
configuration logic that can be used for both configuration and readback.

A connected microcontoller to the SelectMAP interface can load boot
image with bitstream, TF-A (ARM Trusted Firmware) and U-Boot.

This commit adds the missing identification of the SelectMAP mode.

Signed-off-by: Polak, Leszek <LPolak@arri.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Michal Simek <michal.simek@amd.com>
Cc: Stefan Roese <sr@denx.de>
Link: https://lore.kernel.org/r/DU0PR07MB8419F7765892CDBCE7D559C5C8CFA@DU0PR07MB8419.eurprd07.prod.outlook.com
Signed-off-by: Michal Simek <michal.simek@amd.com>

zynqmp_mmio_read/write() are firmware provided hooks that's why use only
zynqmp_firmware.h for function declaration.

Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/e7489556f9e447c737a578c169d7e1e43586a273.1687524706.git.michal.simek@amd.com

Add the missing prototype pointed by below sparse warning
warning: no previous prototype for 'initialize_tcm'
[-Wmissing-prototypes]

Signed-off-by: Algapally Santosh Sagar <santoshsagar.algapally@amd.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230609090531.31794-2-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>

Add missing prototype to fix the sparse warning, warning: no
previous prototype for 'zynqmp_mmio_write' [-Wmissing-prototypes].

Signed-off-by: Algapally Santosh Sagar <santoshsagar.algapally@amd.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230301103334.1455-2-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>

GQSPI driver is using it but this function is never called for Versal
because it is removed by linker. But function should be declared to avoid
this build warning:
drivers/spi/zynqmp_gqspi.c: In function 'zynqmp_qspi_set_tapdelay':
drivers/spi/zynqmp_gqspi.c:378:3: warning: implicit declaration of function
'zynqmp_mmio_write' [-Wimplicit-function-declaration]
  378 |   zynqmp_mmio_write(IOU_TAPDLY_BYPASS_OFST,

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20220825125906.11581-3-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>

On versal platform, enable apb linear mode for apb read and write
execute operations amd disable it when using dma reads. This is done by
xilinx_pm_request() secure calls when CONFIG_ZYNQMP_FIRMWARE is enabled,
else we use direct raw reads and writes in case of mini U-Boot.

Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/20220512100535.16364-5-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@amd.com>

When flash operated at non default mode like DDR, flash need to be reset
to operate in SDR mode to read flash ids by spi-nor framework. Reset the
flash to the default state before using the flash. This reset is handled
by a gpio driver, in case of mini U-Boot as gpio driver is disabled, we
do raw read and write access by the registers.
Versal platform utilizes spi calibration for read delay programming, so
incase by default read delay property is set in DT. We make sure not to
use read delay from DT by overwriting read_delay with -1.

Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/20220512100535.16364-4-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@amd.com>

Platform specific headers are empty that's why there is no need to include
them. That's why remove them for Zynq/ZynqMP and Versal.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/625b1be0b813e2b9a5323c0529f9c567bfe13e75.1643960446.git.michal.simek@xilinx.com