u-boot.git/arch/arm/mach-versal, branch master

xilinx: versal: remove versal loadpdi command

2025-04-16T11:44:44Z

The source code for the versal loadpdi command and the CONFIG_CMD_VERSAL configuration has been removed. It now utilizes the fpga load

command to load secure & non-secure pdi images. Signed-off-by: Prasad Kummari Link: https://lore.kernel.org/r/20250327105200.1262615-4-prasad.kummari@amd.com Signed-off-by: Michal Simek

xilinx: versal: add firmware access to PMC multi Boot mode register

2025-04-16T11:42:06Z

Added extended support for retrieving the PMC muti boot mode register via the firmware interface, which is preferred when U-Boot runs in EL2 and cannot directly access PMC registers via raw reads. Ideally, all secure registers should be accessed via xilinx_pm_request(). Introduced the secure zynqmp_pm_get_pmc_multi_boot_reg() call, which uses xilinx_pm_request() to read the PMC multi boot mode register. BootROM increments the MultiBoot register (PMC_MULTI_BOOT) read address offset by 32 KB and retries. For SD and eMMC boot modes, it can search up to 8191 FAT files for the identification string. A 13-bit mask (0x1FFF) is applied to PMC_MULTI_BOOT_MASK to obtain the correct values in BootROM. Signed-off-by: Prasad Kummari Link: https://lore.kernel.org/r/20250305134845.3182193-1-prasad.kummari@amd.com Signed-off-by: Michal Simek

arm64: zynqmp: versal: Consistently use enum tcm_mode

2025-04-16T11:42:06Z

Turn anonymous enum TCM_LOCK/TCM_SPLIT into enum tcm_mode {}, set TCM_LOCK as 0 and TCM_SPLIT as 1 to match LOCK and SPLIT macros in mach-zynqmp/mp.c, and unify all the functions and their parameters on this one single enum tcm_mode {} instead of a mix of bool and u8. No functional change intended. Signed-off-by: Marek Vasut Tested-by: Love Kumar Link: https://lore.kernel.org/r/20250206213039.42756-1-marex@denx.de Signed-off-by: Michal Simek

Restore patch series "arm: dts: am62-beagleplay: Fix Beagleplay Ethernet"

2024-05-20T19:35:03Z

As part of bringing the master branch back in to next, we need to allow for all of these changes to exist here. Reported-by: Jonas Karlman Signed-off-by: Tom Rini

Revert "Merge patch series "arm: dts: am62-beagleplay: Fix Beagleplay Ethernet""

2024-05-19T14:16:36Z

When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay Ethernet"' I failed to notice that b4 noticed it was based on next and so took that as the base commit and merged that part of next to master. This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35. Reported-by: Jonas Karlman Signed-off-by: Tom Rini

global: Make include

2024-05-06T21:07:48Z

This follows the example of RISC-V where includes directly as "gd" includes a reference to bd_info already and so the first must include the second anyhow. We then remove from all of the places which include references to "gd" an so have already. Signed-off-by: Tom Rini

arm: xilinx: Remove and add needed includes

2024-05-06T21:06:33Z

Remove from all mach-versal-net, mach-versal, mach-zynq and mach-zynqmp files and when needed add missing include files directly. Signed-off-by: Tom Rini

Kconfig: Centralize prompting for SYS_CONFIG_NAME

2024-02-27T19:18:54Z

Generally speaking, we do not prompt for this value and define it in the board specific Kconfig file. There are some valid use cases however today where we do prompt for this value, so instead of having this be done in a number of locations, do this at the top-level location only. This removes the question from a number of other locations and makes it consistent that when we do set the value directly, we always do it the same way. We don't need to specify the type, it's always string. Signed-off-by: Tom Rini

arm64: versal: Add SelectMAP boot mode identification

2023-10-09T11:03:23Z

The SelectMAP configuration interface provides an 8-bit, 16-bit or 32-bit bidirectional data bus interface to the Versal FPGA configuration logic that can be used for both configuration and readback. A connected microcontoller to the SelectMAP interface can load boot image with bitstream, TF-A (ARM Trusted Firmware) and U-Boot. This commit adds the missing identification of the SelectMAP mode. Signed-off-by: Polak, Leszek Reviewed-by: Stefan Roese Cc: Michal Simek Cc: Stefan Roese Link: https://lore.kernel.org/r/DU0PR07MB8419F7765892CDBCE7D559C5C8CFA@DU0PR07MB8419.eurprd07.prod.outlook.com Signed-off-by: Michal Simek

arm64: zynqmp: Fix Siva's email address format

2023-10-09T08:25:32Z

Some patches didn't have his full name and also there was one more ">" at the end of email address. That's why correct both of these issues. Fixes: 174d728471d5 ("arm64: zynqmp: Switch to amd.com emails") Signed-off-by: Michal Simek Link: https://lore.kernel.org/r/e970cc0dfabe293c2baf6b231d34f3af0386f1eb.1695378830.git.michal.simek@amd.com