u-boot.git/arch/arm, branch v2016.05-rc2

Merge branch 'master' of git://git.denx.de/u-boot-socfpga

2016-04-20T13:23:42Z

arm: socfpga: socrates: Add eth0 alias to enable ethernet

2016-04-20T09:28:45Z

This enables full ethernet usage, including U-Boot to write the board specific MAC address (ethaddr) into the DT blob before passing it to Linux. Without this, the ethaddr is not detected in U-Boot at all, resulting in this error upon bootup: ... Model: EBV SOCrates Net: Error: ethernet@ff702000 address not set. No ethernet found. Signed-off-by: Stefan Roese Cc: Marek Vasut Cc: Dinh Nguyen Cc: Chin Liang See

arm: socfpga: Fix typos in DT files (environmnet -> environment)

2016-04-20T09:28:45Z

Fix a small typo in some of the SoCFPGA dts files that has spread via copy-and-paste. Signed-off-by: Stefan Roese Cc: Marek Vasut Cc: Dinh Nguyen Cc: Chin Liang See

ARM: always perform per-CPU GIC init

2016-04-18T21:11:51Z

The current code in ARMv8's lowlevel_init() skips the per-CPU GIC initialization ifndef CONFIG_ARMV8_MULTIENTRY. However, the per-CPU init should always occur; it's just the one-time init that should only happen on the master. Once this consideration is taken into account, the only difference between the paths when CONFIG_ARMV8_MULTIENTRY is undefined/defined is the use of branch_if_slave. Naively, any unified code would need to invoke this conditionally upon ifdef CONFIG_ARMV8_MULTIENTRY. However, branch_if_slave already checks CONFIG_ARMV8_MULTIENTRY and does nothing if it isn't defined, so we don't even need that ifdef at the call site. Reported-by: Masahiro Yamada Signed-off-by: Stephen Warren Reviewed-by: Masahiro Yamada

ARM: AM43xx: Fix BOOT_DEVICE_USB ID

2016-04-18T21:11:44Z

commit 62c5674ea136a ("omap: SPL boot devices cleanup and completion") cleans up the boot device ids for amx3xx soc. But mistakenly updates wrong device IDs for AM43xx USB. Fixing the same here. Signed-off-by: Lokesh Vutla Reviewed-by: Tom Rini

ARM: dts: dra7xx: am57xx: fix cd-gpios definition as per hardware design and dt binding docs

2016-04-18T16:29:19Z

As per mmc device tree binding documentation card detect gpio has to be active low signal. When a hardware is designed with active high card detect, gpio polarity has to be changed with cd-inverted dt property. In DRA72x and AM57xx EVMs the card detect gpio is designed as active low gpio. So correcting the dt card detect gpio definition. Also adding card-detect gpio for DRA74x EVM. Signed-off-by: Mugunthan V N Reviewed-by: Tom Rini

ARM: dts: am43xx: fix cd-gpios definition as per hardware design and dt binding docs

2016-04-18T16:29:18Z

As per mmc device tree binding documentation card detect gpio has to be active low signal. When a hardware is designed with active high card detect, gpio polarity has to be changed with cd-inverted dt property. In AM43xx the card detect gpio is designed as active low gpio. So correcting the dt card detect gpio definition. Signed-off-by: Mugunthan V N Reviewed-by: Tom Rini

Merge branch 'master' of git://www.denx.de/git/u-boot-microblaze

2016-04-13T16:53:11Z

gpio: zynq: Move the definitions to driver file

2016-04-13T16:29:06Z

Move all the gpio definitions to driver file as there is no use of them in other files. Signed-off-by: Siva Durga Prasad Paladugu Signed-off-by: Michal Simek

gpio: zynq: Remove non driver model code

2016-04-13T16:29:06Z

Remove non driver model support as it moved to driver model. Dont need non driver model anymore. Signed-off-by: Siva Durga Prasad Paladugu Signed-off-by: Michal Simek