The architecture is currently unmaintained, remove.

Cc: Benjamin Matthews <mben12@gmail.com>
Cc: Chong Huang <chuang@ucrobotics.com>
Cc: Dimitar Penev <dpn@switchfin.org>
Cc: Haitao Zhang <hzhang@ucrobotics.com>
Cc: I-SYST Micromodule <support@i-syst.com>
Cc: M.Hasewinkel (MHA) <info@ssv-embedded.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Martin Strubel <strubel@section5.ch>
Cc: Peter Meerwald <devel@bct-electronic.com>
Cc: Sonic Zhang <sonic.adi@gmail.com>
Cc: Valentin Yakovenkov <yakovenkov@niistt.ru>
Cc: Wojtek Skulski <info@skutek.com>
Cc: Wojtek Skulski <skulski@pas.rochester.edu>
Signed-off-by: Tom Rini <trini@konsulko.com>

Set up clocks, DDR controller, Nor flash controller, reboot,
serial port. Add new SPI boot modes.

Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Sonic Zhang <sonic.adi@gmail.com>

The bug in the BF526 rom when doing a software reset exists only in older
silicon versions, so don't clear SWRST on newer parts.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Turns out the documentation is wrong and doing "RAISE 1" does not result
in a software reset, only a core reset.  So when the on-chip rom has a
functioning reset helper, use it.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

The bfin_reset_or_hang function unnecessarily duplicates the panic()
logic based on CONFIG_PANIC_HANG.

This patch deletes 20 lines of code and just calls panic() instead.
This also makes the following generic-restart conversion patch simpler.

Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

The hush shell dynamically allocates (and re-allocates) memory for the
argument strings in the "char *argv[]" argument vector passed to
commands.  Any code that modifies these pointers will cause serious
corruption of the malloc data structures and crash U-Boot, so make
sure the compiler can check that no such modifications are being done
by changing the code into "char * const argv[]".

This modification is the result of debugging a strange crash caused
after adding a new command, which used the following argument
processing code which has been working perfectly fine in all Unix
systems since version 6 - but not so in U-Boot:

int main (int argc, char **argv)
{
	while (--argc > 0 && **++argv == '-') {
/* ====> */	while (*++*argv) {
			switch (**argv) {
			case 'd':
				debug++;
				break;
			...
			default:
				usage ();
			}
		}
	}
	...
}

The line marked "====>" will corrupt the malloc data structures and
usually cause U-Boot to crash when the next command gets executed by
the shell.  With the modification, the compiler will prevent this with
an
	error: increment of read-only location '*argv'

N.B.: The code above can be trivially rewritten like this:

	while (--argc > 0 && **++argv == '-') {
		char *arg = *argv;
		while (*++arg) {
			switch (*arg) {
			...

Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>