Xilinx changes for v2022.04-rc3

microblaze:
- Fix exception handler

zynqmp:
- Show information about secure images
- DT changes (som u-boot file removal)
- Fix zynqmp_pm_cfg_obj_convert.py
- Fix platform boot

xilinx:
- Fix bootm_size calculation
- Remove GPIO_EXTRA_HEADER selection

power:
- Add zynqmp power management driver

scsi:
- Add phy support to ceva driver

zynq qspi:
- Fix unaligned accesses and check baudrate setup
- Add support for spi memory operations

net:
- Fix 64bit calculation in axi_emac

video:
- Add missing gpio dependency for seps driver

The correct mask for getting the source/destination register from ESR in
the case of an unaligned access exception is 0x3E0. With this change, a
dummy unaligned store produces the expected info:
"""
>> swi r5, r0, 0x111

 ...
 Hardware exception at 0x111 address
 Unaligned data access exception
 Unaligned word access
 Unaligned store access
 Register R5
 Return address from exception 0x7f99dfc
 ### ERROR ### Please RESET the board ###
"""

Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Link: https://lore.kernel.org/r/20220213080925.1548411-6-ovidiu.panait@windriver.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

The unaligned access messages are only valid in the case of an unaligned
data access exception. Do not print them for other types of hw exceptions.

Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Link: https://lore.kernel.org/r/20220213080925.1548411-5-ovidiu.panait@windriver.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

According to the MicroBlaze reference manual (xilinx2021.2/ug984/page-37):
"""
If an exception is caused by an instruction in a delay slot (that is,
ESR[DS]=1), the exception handler should return execution to
the address stored in BTR instead of the normal exception return
address stored in R17.
"""

Adjust the code to print the proper return address for delay slot
exceptions.

Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Link: https://lore.kernel.org/r/20220213080925.1548411-4-ovidiu.panait@windriver.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

The switch statement in _hw_exception_handler() only covers the
rightmost 5 bits that encode the exception cause:
switch (state & 0x1f)
{
...
}

For this reason, the "0x1000" case will never be reached, because the 13th
bit was zeroed out. To fix this, move delay slot exception handling before
the switch statement (delay slot (DS) bit in Exception Status Register is
independent of the exception cause (EC)).

Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Link: https://lore.kernel.org/r/20220213080925.1548411-3-ovidiu.panait@windriver.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Also, rename it to XILINX_MICROBLAZE0_DELAY_SLOT_EXCEP, since it only
covers delay slot exception support.

Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Link: https://lore.kernel.org/r/20220213080925.1548411-2-ovidiu.panait@windriver.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

The privileged instruction exception seems to have been introduced in
microblaze v7.00 along with MMU support, so having it wrapped in
MICROBLAZE_v5 ifdefs seems incorrect. Move it out of the ifdef, since all
recent microblaze versions support it.

Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Link: https://lore.kernel.org/r/20220213080925.1548411-1-ovidiu.panait@windriver.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

When building for a custom board, it is quite common to maintain a
private branch which include some defconfig and .dts files. But to
hook up those .dts files requires modifying a file "belonging" to
upstream U-Boot, the arch/*/dts/Makefile. Forward-porting that branch
to a newer upstream then often results in a conflict which, while it
is trivial to resolve by hand, makes it harder to have a CI do "try to
build our board against latest upstream".

The .config usually includes information on precisely what .dtb(s) are
needed, so to avoid having to modify the Makefile, simply add the
files in (SPL_)OF_LIST to dtb-y.

A technicality is that (SPL_)OF_LIST is not always defined, so rework
the Kconfig symbols so that (SPL_)OF_LIST is always defined (when
(SPL_)OF_CONTROL), but only prompted for in the cases which used to be
their "depends on".

nios2 and microblaze already have something like this in their
dts/Makefile, and the rationale in commit 41f59f68539 is similar to
the above. So this simply generalizes existing practice. Followup
patches could remove the logic in those two makefiles, just as there's
potential for moving some common boilerplate from all the
arch/*/dts/Makefile files to the new scripts/Makefile.dts.

Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Simon Glass <sjg@chromium.org>

Pull request doc-2022-04-rc1

Replace @return by Return: in code comments.

Sphinx expects Return: and not @return to indicate a return value.

find . -name '*.c' -exec \
sed -i 's/^\(\s\)\*\(\s*\)@return\(\s\)/\1*\2Return:\3/' {} \;

find . -name '*.h' -exec \
sed -i 's/^\(\s\)\*\(\s*\)@return\(\s\)/\1*\2Return:\3/' {} \;

Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>