u-boot.git/arch/mips/cpu, branch v2017.07

MIPS: add initial infrastructure for Broadcom MIPS SoCs

2017-05-10T14:16:09+00:00

CFE checks CPU Thread in a different way (using register $22):
mfc0	t1, C0_BCM_CONFIG, 3 # $22
li	t2, CP0_CMT_TPID # (1 << 31)
and	t1, t2
bnez	t1, 2f	# if we are running on thread 1, skip init
nop

Signed-off-by: Álvaro Fernández Rojas 
Reviewed-by: Simon Glass

MIPS: allow using generic sysreset drivers

2017-05-10T14:16:09+00:00

Avoid duplicating do_reset definition if SYSRESET is enabled for MIPS

Signed-off-by: Álvaro Fernández Rojas 
Reviewed-by: Simon Glass

MIPS: call debug_uart_init right before board_init_f

2017-05-10T14:16:09+00:00

All MIPS boards that support debug uart are calling debug_uart_init right at
the beginning of board_early_init_f.
Instead of doing that, let's provide a generic call to debug_uart_init right
before the call to board_init_f if debug uart is enabled for boards without
stack in SRAM.
On the other hand, boards with stack in SRAM can call earlier (right before
low level init).

Signed-off-by: Daniel Schwierzeck 
Signed-off-by: Álvaro Fernández Rojas

MIPS: add possibility to setup initial stack and global data in SRAM

2016-11-30T15:11:46+00:00

This adds a new Kconfig option CONFIG_MIPS_INIT_STACK_IN_SRAM which
a SoC can select if it supports some kind of SRAM. Together with
CONFIG_SYS_INIT_SP_ADDR the initial stack and global data can be
set up in that SRAM. This can be used to provide a C environment
also for lowlevel_init().

Signed-off-by: Daniel Schwierzeck

MIPS: factor out code for initial stack and global data

2016-11-30T15:11:46+00:00

Move the code for setting up the initial stack and global data
to a macro to be able to use it more than once.

Signed-off-by: Daniel Schwierzeck

MIPS: fix iand optimize setup of CP0 registers

2016-11-30T15:11:46+00:00

Clear cp0 status while preserving implementation specific bits.
Set bits BEV and ERL as the arch specification requires after
a reset or soft-reset exception.

Extend and fix initialization of watch registers. Check if additional
watch register sets are implemented and initialize them too.

Initialize cp0 count as early as possible to get the most
accurate boot timing.

Signed-off-by: Daniel Schwierzeck

MIPS: fix ROM exception vectors

2016-11-30T15:11:39+00:00

When booting from ROM, early exceptions can't be handled
properly. Instead of busy-looping give the developer the
possibilty to examine the situation. Invoke an UHI
exception operation which can be read as unhandled exception
by a hardware debugger if one is attached. If the debugger
doesn't support UHI, the exception is read as unexpected
breakpoint.

Signed-off-by: Daniel Schwierzeck

MIPS: make inclusion of ROM exception vectors configurable

2016-11-30T15:07:17+00:00

This adds a compile time option to include code for static
exception vectors. Static exception vectors are only needed,
when the U-Boot entry point is equal to the CPU reset exception
vector address. For instance this is the case when U-Boot is
used as ROM in Qemu or booted from parallel NOR flash. When
U-Boot is booted from RAM (e.g. loaded there by SPL), the
exception vectors need to be setup dynamically, which is done
in follow-up commits.

Signed-off-by: Daniel Schwierzeck

MIPS: Hang if run on a secondary CPU

2016-09-21T15:04:53+00:00

Some systems are configured such that multiple CPUs begin running from
their reset vector following a system reset. If this occurs then U-Boot
will be run on multiple CPUs simultaneously, which causes all sorts of
issues as the multiple instances of U-Boot clobber each other.

Prevent this from happening by simply hanging with an infinite loop if
we run on a CPU whose ID, as determined by GlobalNumber or EBase.CPUNum
as appropriate, is non-zero.

Signed-off-by: Paul Burton

MIPS: Fix cache maintenance in relocate_code & simplify

2016-09-21T14:25:43+00:00

The relocate_code function was handling cache maintenance incorrectly.
It copied U-Boot to its new location, flushed the caches & then
proceeded to apply relocations & jump to the new code without flushing
the caches again. This is problematic as the instruction cache could
potentially have already fetched instructions that hadn't had relocs
applied.

Rework this to perform the flush_cache call using the code in the
original copy of U-Boot, after having applied relocations to the new
copy of U-Boot. The new U-Boot can then be jumped to safely once that
cache flush has been performed.

As part of this, since the old U-Boot is used up until after that cache
flush, complexity around loading values from the GOT using a jump & link
instruction & loads from a table is removed. Instead we can simply load
the needed values with PTR_LA fromt the original GOT.

Signed-off-by: Paul Burton