u-boot.git/arch/mips/dts, branch v2020.07

mips: Add support for SoM "VoCore2".

2020-04-27T18:30:14Z

Small patch to add support for VoCore/VoCore2 board. VoCore is open hardware and runs OpenWrt/LEDE. It has WIFI, USB, UART, 20+ GPIOs but is only one inch square. It will help you to make a smart house, study embedded system or even make the tiniest router in the world. Details about this SoM can be found at "https://vocore.io/v2.html". Signed-off-by: Mauro Condarelli Reviewed-by: Stefan Roese

mips: mtmips: add support for mt7628-rfb

2020-04-27T18:30:13Z

This patch adds support for mt7628 reference board. SPL_DM and DT are not enabled for SPL to save about 17KiB for u-boot-spl.bin. Reviewed-by: Stefan Roese Signed-off-by: Weijie Gao

mips: mtmips: add SPL support

2020-04-27T18:30:12Z

This patch adds SPL support for mtmips platform. The lowlevel architecture is split into SPL and the rest parts are built into a memory loadable u-boot image. Optional SPL_DM and OF_CONTROL are also supported. The increment of size is very small (< 10 KiB) if SPL_DM and OF_CONTROL are not enabled and the memory bootable u-boot (u-boot.img) is generated automatically so there is not need to add a separate config for it. A lzma compressed payload (u-boot-lzma.img) is also generated and it will be combined with u-boot-spl.bin to form the unified ROM bootable binary u-boot-mtmips.bin. A spl loader is added to support uncompress the payload. Reviewed-by: Stefan Roese Signed-off-by: Weijie Gao

dts: mtmips: add alternative pinmux node for uart2

2020-04-27T18:29:33Z

This patch adds a new pinmux for UART2, which shares the pins with SPIS. Reviewed-by: Stefan Roese Signed-off-by: Weijie Gao

mips: mtmips: make use of sysreset-resetctrl for mt7628 soc

2020-04-27T18:29:33Z

This patch replaces sysreset-syscon with sysreset-resetctrl for mt7628 soc. Reviewed-by: Stefan Roese Reviewed-by: Daniel Schwierzeck Signed-off-by: Weijie Gao

dts: mtmips: add default pinctrl to eth nodes for all boards

2019-10-25T15:20:44Z

This patch adds default eth pinctrl for all boards. There are two pinctrl nodes used for two scenarios: ephy_iot_mode - for IOT boards which have only one port (PHY0) ephy_router_mode - For routers which have more than one ports Reviewed-by: Stefan Roese Signed-off-by: Weijie Gao

dts: mtmips: add default pinctrl for gardena-smart-gateway-mt7688

2019-10-25T15:20:44Z

This adds default pinctrl (dual SPI chip select) for gardena smart gateway Reviewed-by: Stefan Roese Signed-off-by: Weijie Gao

dts: mtmips: add mmc related nodes for mt7628an.dtsi

2019-10-25T15:20:44Z

This patch adds mmc related nodes for mt7628an.dtsi Signed-off-by: Weijie Gao

dts: mtmips: enable eth port0 led and link poll functions for all boards

2019-10-25T15:20:44Z

This patch adds default p0led status and phy0 link polling for all boards. Reviewed-by: Stefan Roese Signed-off-by: Weijie Gao

dts: mtmips: update reset controller node for mt7628

2019-10-25T15:20:44Z

This patch updates reset controller node for mt7628 Signed-off-by: Weijie Gao