u-boot.git/arch/powerpc/include, branch v2023.07

powerpc: mpc885: Add CPM USB-SOF microcode for CPM15 ERRATA

2023-05-05T05:26:53Z

MPC885 CPU has the following ERRATA: When the USB controller is configured in Host mode, and the SOF generation (SFTE=1 in USMOD register) is being used, there may be false CRC error indication in other SCCs. Although the data is received correctly, the CRC result will be corrupted. Add capability to load the related microcode to fix it. The microcode binary data is copied from Linux kernel. Other microcode will be added in following patch so make it a Kconfig choice. Signed-off-by: Christophe Leroy

powerpc: Force cast on memcpy_toio()

2023-05-05T05:26:53Z

sparse reports the following warning: CHECK arch/powerpc/cpu/mpc8xx/micropatch_usb_sof.c arch/powerpc/cpu/mpc8xx/micropatch_usb_sof.c:29:9: warning: cast removes address space '' of expression arch/powerpc/cpu/mpc8xx/micropatch_usb_sof.c:30:9: warning: cast removes address space '' of expression This is because of (void *) casts for using memcpy() as a substitute. Do like other architectures, __force the cast to silence the warning Signed-off-by: Christophe Leroy

powerpc: mpc8xx: Reorganise init RAM

2023-05-04T10:40:47Z

Using SMC relocation microcode patch or USB-SOF microcode patch will disable DPRAM memory from 0x2000 to 0x2400 and from 0x2f00 to 0x3000. At the time being, init RAM is setup to use 0x2800-0x2e00, but the stack pointer goes beyond 0x2800 and even beyond 0x2400. For the time being we are not going to use any microcode patch that uses memory about 0x3000, so reorganise setup to use: - 0x2800 - 0x2e00 for init malloc and global data and CPM buffers - 0x3000 - 0x3c00 for init stack For more details about CPM dual port ram, see commit b1d62424cb ("powerpc: mpc8xx: redistribute data in CPM dpram") Signed-off-by: Christophe Leroy

powerpc: mpc8xx: CPM parameter RAM can be anywhere

2023-05-04T08:58:07Z

With relocation, CPM parameter RAM can be anywhere in the dual port RAM, so don't split dual port RAM. Remove dparam and dparam16 members of struct comm_proc PROFF_XXX become offsets from the start of dual port RAM, then they are now consistant with the offsets in RPBASE registers. Signed-off-by: Christophe Leroy

spi: mpc8xxx: Add support for SPI on mpc832x

2023-04-06T12:50:03Z

On mpc832x, SPI can be either handled by CPU or QE. In order to work in CPU mode, bit 17 of SPMODE has to be set to 1, that bit is called OP. Also, data is located at a different place than the one expected by the driver today. In 8 bits mode with REV set, data to be transmitted is located in the most significant byte while received data is located in second byte. So perform the necessary shifts. In order to differentiate with other CPUs, a new compatible is added for mpc832x: fsl,mpc832x-spi Signed-off-by: Christophe Leroy Cc: Rasmus Villemoes

gpio: Add QUICC Engine GPIOs driver

2023-04-06T12:50:03Z

The mpc832x has GPIOs handled by the QUICC Engine. The registers are different from the one for the non QE mpc83xx GPIOs. Implement a GPIO driver for those. Signed-off-by: Christophe Leroy

powerpc: mpc83xx: Fix soc.h

2023-04-06T12:50:03Z

There are helpers included in soc.h Declare them static inline so that soc.h can be included in several places. Signed-off-by: Christophe Leroy

driver, gpio: Add support for MPC 8xx CPU ports

2023-02-11T07:47:58Z

Ports A, C and D are 16 bits ports. Ports B and E are 32 bits ports. The "compatible" is used to determine each port type. This patch was originally written by Charles Frey who's email address is not valid anymore as he left the company. Signed-off-by: Christophe Leroy Reviewed-by: FRANJOU Stephane

global: Finish CONFIG -> CFG migration

2023-01-20T17:27:24Z

At this point, the remaining places where we have a symbol that is defined as CONFIG_... are in fairly odd locations. While as much dead code has been removed as possible, some of these locations are simply less obvious at first. In other cases, this code is used, but was defined in such a way as to have been missed by earlier checks. Perform a rename of all such remaining symbols to be CFG_... rather than CONFIG_... Signed-off-by: Tom Rini Reviewed-by: Simon Glass

nxp: Finish migration of SYS_FSL_SRDS_[12] to Kconfig

2023-01-20T17:27:23Z

As this is used on both ARM and PowerPC platforms, this needs to be listed in arch/Kconfig.nxp and match how they're currently used by select'ing them under the required PowerPC ARCH_xxx options. Signed-off-by: Tom Rini