An empty flush_dcache_range() was added into MPC83xx and MPC85xx to
work with drivers shared with other architecture.  However, it is
compiled only if USB is set, but it is required for other drivers
(FSL_ESDHC), too.

Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Andy Fleming <afleming@gmail.com>
CC: Dirk Behme <dirk.behme@de.bosch.com>
CC: Marek Vasut <marex@denx.de>
CC: Wolfgang Denk <wd@denx.de>

Added MPC83xx version.

Signed-off-by: Wolfgang Denk <wd@denx.de>

* 'master' of git://git.denx.de/u-boot-mpc85xx:
  powerpc/mpc85xx: Fix Handling the lack of L2 cache on P2040/P2040E
  powerpc/mpc85xx: Workaround for erratum CPU_A011
  powerpc/mpc85xx: Ignore E bit for SVR_SOC_VER()
  powerpc/P4080: Check SVR for CPU22 workaround
  lib/powerpc: addrmap_phys_to_virt() should return a pointer
  powerpc/85xx: clean up P1022DS board configuration header file
  powerpc/85xx: fdt_set_phy_handle() should return an error code
  powerpc/85xx: minor clean-ups to the P2020DS board header file
  powerpc/p1010rdb: add readme document for p1010rdb
  powerpc/mpc85xx:NAND_SPL:Avoid IFC/eLBC Base address setting
  powerpc/mpc85xx:Add debugger support for e500v2 SoC
  powerpc/85xx:Fix NAND code base to support debugger
  powerpc/85xx:Make debug exception vector accessible
  powerpc/85xx:Fix MSR[DE] bit in MSR to support debugger
  PATCH 1/4][v4] doc:Add documentation for e500 external debugger support
  powerpc/p1010rdb: update mux config of p1010rdb board
  powerpc/mpc85xx:Add BSC9131 RDB Support
  powerpc/mpc85xx:Add BSC9131/BSC9130/BSC9231 Processor Support
  powerpc/85xx: Add USB device-tree fixup for various platforms

Signed-off-by: Wolfgang Denk <wd@denx.de>

Fix SVR checking for commit acf3f8da.

Signed-off-by: York Sun <yorksun@freescale.com>

Erratum NMG_CPU_A011 applies to P4080 rev 1.0, 2.0, fixed in rev 3.0.
It also applies to P3041 rev 1.0, 1.1, P2041 rev 1.0, 1.1. It shares the
same workaround as erratum CPU22. Rearrange registers usage in assembly
code to avoid accidental overwriting.

Signed-off-by: York Sun <yorksun@freescale.com>

We don't care E bit of SVR in most cases. Clear E bit for SVR_SOC_VER().
This will simplify the coding. Use IS_E_PROCESSOR() to identify SoC with
encryption. Remove all _E entries from SVR list and CPU list.

Signed-off-by: York Sun <yorksun@freescale.com>

Workaround for erratum CPU22 applies to P4080 rev 1 and rev 2 only.

Signed-off-by: York Sun <yorksun@freescale.com>

addrmap_phys_to_virt() converts a physical address (phys_addr_t) to a
virtual address, so it should return a pointer instead of an unsigned long.
Its counterpart, addrmap_virt_to_phys(), takes a pointer, so now they're
orthogonal.

The only caller of addrmap_phys_to_virt() converts the return value to
a pointer anyway.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>

During NAND_SPL boot, base address and different register are programmed
default by corresponding NAND controllers(eLBC/IFC). These settings are
sufficient enough for NAND SPL.

Avoid updating these register.They will be programmed during NAND RAMBOOT.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>

Freescale's e500v1 and e500v2 cores (used in mpc85xx chips) have some
restrictions on external debugging (JTAG).

So define CONFIG_SYS_PPC_E500_DEBUG_TLB to enable a temporary TLB entry to be
used during boot to work around the limitations.

Please refer doc/README.mpc85xx for more information

Signed-off-by: Radu Lazarescu <radu.lazarescu@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>

Update NAND code base to ovecome e500 and e500v2's second limitation i.e. IVPR
+ IVOR15 should be valid fetchable OP code address.

As NAND SPL does not compile vector table so making sure IVOR + IVOR15 points to
any fetchable valid data

Signed-off-by: Radu Lazarescu <radu.lazarescu@freescale.com>
Signed-off-by: Marius Grigoras <marius.grigoras@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>