u-boot.git/arch/powerpc, branch v2018.11

powerpc: t1040: Correct RCW EC2 settings

2018-10-29T20:19:43Z

Per T1040RM (Rev. 1, 08/2015), there are 2 issues with the RCW EC2 settings. - The value of FSL_CORENET_RCWSR13_EC2_FM1_GPIO is wrong and should be 0x04000000 (value of 1 in RCW bit [420:421]) - Value of 2/3 are reserved in RCW bit [420:421], hence there is no macro FSL_CORENET_RCWSR13_EC2_FM1_DTSEC5_MII. Signed-off-by: Bin Meng Acked-by: Poonam Aggrwal Reviewed-by: York Sun

powerpc: t1040: Correct RCW MAC2_GMII_SEL value

2018-10-29T20:13:33Z

Per T1040RM (Rev. 1, 08/2015), the value of FSL_CORENET_RCWSR13_MAC2_GMII_SEL_ENET_PORT is wrong and should be 0x00000080 (bit 440 in the RCW). Signed-off-by: Bin Meng Acked-by: Poonam Aggrwal Reviewed-by: York Sun

fsl/usb: Workaround for USB erratum-A005275

2018-10-29T20:13:05Z

Workaround makes FS as default mode on all affected socs. Add support to check erratum-A005275 validity for an soc. This info is required to determine whether a given soc is affected by this erratum. Add quirk for this erratum "has_fsl_erratum_a005275" . This quirk is used to enable workaround for the errata Force FS mode as default by: - making EPS as FS - setting PFSC bit to disable HS chirping This workaround can be disabled by mentioning "no_erratum_a005275" in hwconfig string Signed-off-by: Chris Packham Reviewed-by: York Sun

powerpc: dts: Enable device tree support for T2080QDS

2018-09-27T17:14:14Z

Add device tree for T2080QDS board and enable CONFIG_OF_CONTROL so that device tree can be compiled. Update board README for device tree usage. Signed-off-by: Jagdish Gediya Reviewed-by: Bin Meng Reviewed-by: Simon Glass Reviewed-by: York Sun

powerpc: dts: Add u-boot.dtsi to use binman for MPC85xx boards

2018-09-27T17:14:06Z

Signed-off-by: Jagdish Gediya Reviewed-by: Bin Meng Reviewed-by: Simon Glass Reviewed-by: York Sun

powerpc: mpc85xx: Use binman to embed dtb inside U-Boot

2018-09-27T17:13:59Z

Below is the sequence to embed dtb inside U-Boot, 1. Remove bootpg and resetvec section if needed 2. Append dtb 3. Append bootpg and resetvec section back if removed in step 1 Above procedure is required only when CONFIG_MPC85xx and CONFIG_OF_SEPARATE are defined. Add new config CONFIG_MPC85XX_HAVE_RESET_VECTOR to indicate that image has resetvec section. Step 1 and step 3 described above are required only if this config is y. Signed-off-by: Jagdish Gediya Reviewed-by: Simon Glass Reviewed-by: York Sun

powerpc: mpc85xx: Select BINMAN by default

2018-09-27T17:13:55Z

Signed-off-by: Jagdish Gediya Reviewed-by: Bin Meng Reviewed-by: Simon Glass Reviewed-by: York Sun

powerpc/dts: Makefile changes to clean and build dts

2018-09-27T17:13:38Z

Signed-off-by: Jagdish Gediya Reviewed-by: Bin Meng Reviewed-by: Simon Glass Reviewed-by: York Sun

powerpc/dts: Define '_end' symbol in mpc85xx U-Boot lds files

2018-09-27T17:13:24Z

'board_fdt_blob_setup' function sets up fdt blob at '&_end' so define '_end' symbol in mpc85xx lds files. Signed-off-by: Jagdish Gediya Reviewed-by: Simon Glass Reviewed-by: Bin Meng Reviewed-by: York Sun

misc: Add MPC83xx serdes driver

2018-09-18T14:12:21Z

Add a driver to configure the SerDes (Serializer/Deserializer) lanes on the MPC83xx architecture. Reviewed-by: Simon Glass Signed-off-by: Mario Six