u-boot.git/arch/sandbox/cpu/start.c, branch v2018.11

sandbox: Remove the old memory file later

2018-10-09T10:40:26Z

When debugging sandbox it is sometimes annoying that the memory file is deleted early on. If sandbox later crashes or we quit (using the debugger), it is not possible to run it again with the same state since the memory file is gone. Remove the old memory file when sandbox exits, instead. Also add debugging showing the memory filename. Signed-off-by: Simon Glass

sandbox: Add a flag to set the default log level

2018-10-09T10:40:26Z

It is useful to be able to set the default log level from the command line when running sandbox. Add a new -L command-line flag for this. The log level is set using the enum log_level_t in log.h. At present a number must be specified, e.g. -L7 for debug. Signed-off-by: Simon Glass

SPDX: Convert all of our single license tags to Linux Kernel style

2018-05-07T13:34:12Z

When U-Boot started using SPDX tags we were among the early adopters and there weren't a lot of other examples to borrow from. So we picked the area of the file that usually had a full license text and replaced it with an appropriate SPDX-License-Identifier: entry. Since then, the Linux Kernel has adopted SPDX tags and they place it as the very first line in a file (except where shebangs are used, then it's second line) and with slightly different comment styles than us. In part due to community overlap, in part due to better tag visibility and in part for other minor reasons, switch over to that style. This commit changes all instances where we have a single declared license in the tag as both the before and after are identical in tag contents. There's also a few places where I found we did not have a tag and have introduced one. Signed-off-by: Tom Rini

sandbox: use CONFIG_VAL(SYS_MALLOC_F_LEN) to distinguish malloc pool size before relocation

2017-07-27T12:59:04Z

SPL and normal u-boot stage use different malloc pool size configuration before relocation, so use CONFIG_VAL(SYS_MALLOC_F_LEN) to fit different boot stage. Signed-off-by: Andy Yan Changes in v3: - use CONFIG_VAL(), which suggested by Simon Changes in v2: None arch/sandbox/cpu/start.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) Acked-by: Philipp Tomsich Reviewed-by: Philipp Tomsich

board_f: sandbox: Move sandbox_early_getopt_check() into misc_init_f()

2017-04-05T17:55:07Z

We don't need a special hook for sandbox as one of the later ones will do just as well. We can print error messages about bad options after we print the banner. In fact, it seems better. Signed-off-by: Simon Glass Reviewed-by: Stefan Roese

board_f: sandbox: Move setup_ram_buf() to private code

2017-04-05T17:52:35Z

There is no need to have this call in the generic init sequence and no other architecture has needed it in the time it has been there. Move it into sandbox's private code. Signed-off-by: Simon Glass Reviewed-by: Stefan Roese Reviewed-by: Stefan Roese

sandbox: Don't include the main loop in SPL

2016-07-15T02:40:24Z

SPL does not have a command interface so we should not include the main loop code. Signed-off-by: Simon Glass

sandbox: Avoid calling commands when not available

2016-03-22T16:16:10Z

Don't try to run commands when not supported. Signed-off-by: Simon Glass Reviewed-by: Tom Rini

test: Record and silence console in tests

2015-11-20T03:27:51Z

When running sandbox tests, silence the console to avoid unwanted output. Also, record the console in case tests want to check it. The -v option can be used to enable stdout during tests. Signed-off-by: Simon Glass

sandbox: Add missing errno.h includes in a few files

2015-05-15T00:49:34Z

These files use error numbering, so add the include. Signed-off-by: Simon Glass