Unnamed repository; edit this file 'description' to name the repository. http://cgit.235523.xyz/u-boot.git/atom/arch?h=v2012.07-rc1 2012-07-10T06:54:41Z 2012-07-10T06:54:41Z Wolfgang Denk wd@denx.de 2012-07-10T06:54:41Z urn:sha1:895f3e0542015b347298c8b501e63d5f32002c04 * 'master' of git://git.denx.de/u-boot-arm: tegra: define fdt_load/fdt_high variables tegra: enable bootz command tegra: usb: Fix device enumeration problem of USB1 tegra: trimslice: set up serial flash pinmux tegra: add pin_mux_spi() board initialization function tegra: add GMC/GMD funcmux entry for SFLASH tegra: bootcmd: start USB only when needed tegra: bootcmd enhancements tegra: add enterrcm command tegra: enable CONFIG_ENV_VARS_UBOOT_CONFIG Add env vars describing U-Boot target board tegra: usb: fix wrong error check tegra: add ULPI on USB2 funcmux entry tegra: fix leftover CONFIG_TEGRA2_MMC & _SPI build switches tegra: Add Tamonten Evaluation Carrier support tegra: Use SD write-protect GPIO on Tamonten tegra: Implement gpio_early_init() on Tamonten tegra: Allow boards to perform early GPIO setup tegra: plutux: Add device tree support tegra: medcom: Add device tree support tegra: Rework Tamonten support beagle: add eeprom expansion board info for bct brettl4 Signed-off-by: Wolfgang Denk <wd@denx.de> 2012-07-10T06:50:05Z Rajeshwari Shinde rajeshwari.s@samsung.com 2012-07-09T19:34:34Z urn:sha1:30704dae469c092766c346b3bef7ac001fa45511 Fixed the compiler warning message. Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> Acked-by: Marek Vasut <marex@denx.de> 2012-07-09T21:59:00Z Wolfgang Denk wd@denx.de 2012-07-09T21:59:00Z urn:sha1:ba662f8998f67b31d88bf3a78970ad8375e5644a * 'master' of git://git.denx.de/u-boot-usb: CONFIG: EXYNOS5: USB: Enable USB 2.0 on smdk5250 EXYNOS5: USB: Fix incorrect USB base addresses EXYNOS: Add power Enable/Disable for USB-EHCI USB: EXYNOS: Set USB 2.0 HOST Link mode EXYNOS5: Add structure for PMU registers EXYNOS5: Fix system register structure USB: EXYNOS: Incorporate EHCI review comments Signed-off-by: Wolfgang Denk <wd@denx.de> 2012-07-09T20:44:34Z Jim Lin jilin@nvidia.com 2012-06-24T20:40:57Z urn:sha1:8b3f7bf7ec95816a7d2f89331e8877a351b3ec7c A known hardware issue of USB1 port where bit 1 (connect status change) of PORTSC register will be set after issuing Port Reset (like "usb reset" in u-boot command line). This will be treated as an error and stops later device enumeration. Therefore we clear that bit after Port Reset in order to proceed later device enumeration. Signed-off-by: Jim Lin <jilin@nvidia.com> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Tom Warren <twarren@nvidia.com> 2012-07-09T20:44:33Z Stephen Warren swarren@nvidia.com 2012-06-12T08:33:39Z urn:sha1:a016e144ed6a7e17774d3371c29544c329459667 This is used on TrimSlice. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com> 2012-07-09T20:44:33Z Stephen Warren swarren@nvidia.com 2012-06-04T09:23:55Z urn:sha1:9cd3f3adf03bdbc5ea4514f00e2cfacfb1ae5bed Tegra's boot ROM supports a mode whereby code may be downloaded and flash programmed over a USB connection. On dev boards, this is typically entered by holding down a "force recovery" button and resetting the CPU. However, not all boards have such a button (one example is the Compulab Trimslice), so a method to enter RCM from software is useful. This change implements the command "enterrcm" to do this, and enables it for all Tegra boards by default. Even on boards other than Trimslice, controlling this over a UART may be useful, e.g. to allow simple remote control without the need for mechanical button actuators, or hooking up relays/... to the button. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com> 2012-07-09T20:44:33Z Lucas Stach dev@lynxeye.de 2012-05-31T01:51:02Z urn:sha1:f857fff6068fe36a327a0ff6d837412caaf2e07d loop_count runs down from 10000, so the correct condition to error out is ==0. Signed-off-by: Lucas Stach <dev@lynxeye.de> Acked-by: Stephen Warren <swarren@wwwdotorg.org> CC: Stephen Warren <swarren@wwwdotorg.org> CC: Tom Warren <twarren.nvidia@gmail.com> Tested-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Tom Warren <twarren@nvidia.com> 2012-07-09T20:44:33Z Lucas Stach dev@lynxeye.de 2012-05-31T01:51:01Z urn:sha1:f97daaa2317b68aacfbf19bb7566183e17db3349 This is needed as a prerequisite for Tegra USB ULPI support within U-Boot. Signed-off-by: Lucas Stach <dev@lynxeye.de> Acked-by: Stephen Warren <swarren@wwwdotorg.org> CC: Stephen Warren <swarren@wwwdotorg.org> CC: Tom Warren <twarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com> 2012-07-09T16:27:55Z Rajeshwari Shinde rajeshwari.s@samsung.com 2012-05-14T05:52:04Z urn:sha1:86d74d03391a4a3b35cfdbdeff0de2c245bf1910 This patch corrects the base addresses for USB_PHY and USB_OTG. Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com> Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> Acked-by: Chander Kashyap <chander.kashyap@linaro.org> Acked-by: Minkyu Kang <mk7.kang@samsung.com> 2012-07-09T16:27:55Z Rajeshwari Shinde rajeshwari.s@samsung.com 2012-05-14T05:52:03Z urn:sha1:c48ac11322800d6492ea31f42ca53301a444742a This patch adds functions to enable/disable the power of USB host controller for EXYNOS5. Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com> Signed-off-by: Che-Liang Chiou <clchiou@chromium.org> Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>