u-boot.git/arch, branch v2016.05-rc3

ARM: DRA7: Add ABB setup for all domains

2016-04-25T19:10:41Z

ABB should be initialized for all required domains voltage domain for DRA7: IVA, GPU, EVE in addition to the existing MPU domain. If we do not do this, kernel configuring just the frequency using the default boot loader configured voltage can fail on many corner lot units and has been hard to debug. This specifically is a concern with DRA7 generation of SoCs since other than VDD_MPU, all other domains are only permitted to setup the voltages to required OPP only at boot. Reported-by: Richard Woodruff Signed-off-by: Nishanth Menon

ARM: OMAP5: Enable ABB configuration for MM voltage domain

2016-04-25T19:10:40Z

Since we setup the voltage and frequency for the MM domain, we *must* setup the ABB configuration needed for the domain as well. If we do not do this, kernel configuring just the frequency using the default boot loader configured voltage can fail on many corner lot units. Reported-by: Richard Woodruff Signed-off-by: Nishanth Menon

ARM: OMAP5/DRA7: Move ABB TXDONE mask to voltage structure

2016-04-25T19:10:39Z

ABB TX_DONE mask will vary depending on ABB module. For example, 3630 never had ABB on IVA domain, while OMAP5 does use ABB on MM domain, DRA7 has it on all domains with the exception of CORE, RTC. Hence, move the txdone mask definition over to structure describing voltage domain. Signed-off-by: Nishanth Menon

ARM: OMAP5/DRA7: Get rid of control_std_fuse_opp_vdd_mpu_2

2016-04-25T19:10:38Z

This information is already available under vcores->volts.efuse.reg. There is no reason for duplicating the information since AVS Class 0 definitions are common for OMAP5 and DRA7 and defined with STD_FUSE_OPP_* macros. This allows a central location of defining the ABB and voltage definitions especially since they are reused. This also makes it simpler to prevent mistakes involved when changing the boot OPP for the device. Signed-off-by: Nishanth Menon

ARM: hisilicon: hikey: dts: Add pl011 additional clock binding.

2016-04-25T19:10:34Z

This is a binding which only exists in U-Boot, but is required to get working serial in U-Boot. Signed-off-by: Peter Griffin Reviewed-by: Tom Rini

ARM: hisilicon: hikey: Enable OF_CONTROL for hikey board.

2016-04-25T19:10:34Z

Currently only the serial pl01x driver is using DT, and the other drivers still use platform data but as more DT lands in the upstream kernel the aim is to migrate the other drivers over to DT as well to have a fully DT configured hikey u-boot. Signed-off-by: Peter Griffin Reviewed-by: Tom Rini

ARM: hisilicon: hikey: Add hikey & hi6220 dts from v4.6-rc3.

2016-04-25T19:10:31Z

Import the upstream kernel dts into U-Boot. Currently only serial is supported, but a lot more DT changes are queued for v4.7. Signed-off-by: Peter Griffin Reviewed-by: Tom Rini

configs: Re-sync with cmd/Kconfig

2016-04-25T19:09:47Z

Update the config.h and defconfig files for the commands that 8e3c036 converted over to Kconfig Signed-off-by: Tom Rini

configs: Re-sync almost all of cmd/Kconfig

2016-04-25T19:09:40Z

This syncs up the current cmd/Kconfig and include/configs/ files with the only exception being CMD_NAND. Due to how we have used this historically we need to take further care here when converting. Signed-off-by: Tom Rini

Merge branch 'master' of git://www.denx.de/git/u-boot-uniphier

2016-04-25T17:45:32Z