u-boot.git/arch, branch v2019.01-rc2

Merge tag 'for-master-20181216' of git://git.denx.de/u-boot-rockchip

2018-12-17T01:49:46Z

Improvements and fixes or u-boot-rockchip: - new board: adds rv1108-elgin-r1 board support - rk3288-evb: dts: remove 'vmmc' from emmc node - rk3399-puma: dts: remove obsolete DTS node 'vcc5v0_host'

ARM: rockchip: Add rv1108-elgin-r1 board support

2018-12-16T00:30:11Z

Add the initial support for Elgin R1 board, which is based on the RV1108 SoC and has the following features currently supported in U-Boot: - UART - eMMC - USB Signed-off-by: Otavio Salvador Reviewed-by: Philipp Tomsich

Merge branch 'master' of git://git.denx.de/u-boot-usb

2018-12-15T22:49:57Z

- Second half of the USB Gadget DM conversion

rockchip: rk3288-evb: dts: remove 'vmmc' from emmc node

2018-12-15T19:56:46Z

This is a sync with kernel mainline dts. The U-Boot eMMC does not need to care about the power for Rockchip SoCs, because if the board is using eMMC, the power will default on (for bootrom), so the 'vmmc', 'vqmmc' is only useful for SD in U-Boot. Signed-off-by: Kever Yang Reviewed-by: Philipp Tomsich

rockchip: rk3399-puma: Remove obsolete DTS node 'vcc5v0_host'.

2018-12-15T19:56:26Z

vcc5v0_host and usbhub_enable share gpio4 RK_PA3, which is a problem during probing (the second probe will trigger a -EBUSY, when trying to get the gpio handle). An analysis of the situation shows, that both regulators are actually describing the same supply. This patch removes the (currenlty not successful probing) regulator vcc5v0_host from the DTS and adds the pinctrl-* setting to usbhub_enable. Signed-off-by: Christoph Muellner Reviewed-by: Phiilipp Tomsich

poplar: fix boot failure caused by serial driver change

2018-12-15T16:49:56Z

Commit 4687919684e0 ("serial: Remove DM_FLAG_PRE_RELOC flag in various drivers") essentially drops flag DM_FLAG_PRE_RELOC from serial_pl01x driver for Poplar platform, because the platform falls into the following strategy category made by the commit. Surround DM_FLAG_PRE_RELOC flag with OF_CONTROL check, for drivers that support both statically declared devices and configuration from device tree Before the commit lands, Poplar platform works by statically declaring pl011 serial device via U_BOOT_DEVICE() with DM_FLAG_PRE_RELOC flag set in the driver. But since Poplar also supports device configuration from device tree, the commit practically drops the flag for Poplar, and hence breaks the platform from booting. This patch changes platform code and device tree to initiate pl011 serial device from device tree rather than static declaration, so that above strategy about DM_FLAG_PRE_RELOC applies to Poplar, and therefore the reported boot failure gets fixed. Reported-by: Igor Opaniuk Fixes: 4687919684e0 ("serial: Remove DM_FLAG_PRE_RELOC flag in various drivers") Cc: Bin Meng Cc: Simon Glass Signed-off-by: Shawn Guo Reviewed-by: Igor Opaniuk Tested-by: Igor Opaniuk Reviewed-by: Bin Meng

arm: am33xx: Register USB controllers if DM_USB is used but not OF_CONTROL

2018-12-14T16:59:10Z

When DM_USB is used, either the USB controllers are bound when the DTB is parsed (when OF_CONTROL is enabled) or they are bound using the U_BOOT_DEVICES() macro. In the later case, the platform data is passed in a struct ti_musb_platdata because it cannot be read from the DTB. Signed-off-by: Jean-Jacques Hiblot Reviewed-by: Tom Rini

usb: musb-new: Add support for DM_USB

2018-12-14T16:59:10Z

Enable DM for USB peripheral in the musb-new driver. Also make sure that the driver can be used in the SPL. This implies that: * the driver must work with and without the OF_CONTROL option. That in turn, implies that the platform data can be passed in a struct ti_musb_platdata or be read from the dtb * usb.o is linked in the SPL if host support is enabled Another change is that the driver does not fail to bind (and stop the boot process) if one of the child driver does not bind. Reporting the error is enough. This kind of error would appear if the port is configured in the DTS but the driver is not activated in the config. Signed-off-by: Jean-Jacques Hiblot Reviewed-by: Tom Rini

dts: am4372: Enable USB1 in SPL

2018-12-14T16:59:10Z

USB1 can be used by the romboot on all am4372 platforms to download a firmware (SPL in our case). It makes sense to enable USB1 in the SPL to download u-boot. Signed-off-by: Jean-Jacques Hiblot Reviewed-by: Tom Rini

dts: Add a u-boot specific dtsi file for the am4372

2018-12-14T16:59:09Z

This file is used to override the values found in am4372.dtsi Use it to fix the "compatible" options for the controllers used to support the USB (parent bus and syscons). Signed-off-by: Jean-Jacques Hiblot Reviewed-by: Tom Rini