u-boot.git/arch, branch v2025.04-rc2

Merge patch series "Enable MCU ESM reset"

2025-02-10T16:32:03Z

Judith Mendez says: This patch series enables ESM reset configuration in board_init_f for am62x and am62px devices. This is necessary in order for error events to reset the system. This patches are tested using watchdog to reset the system via ESM. Link: https://lore.kernel.org/r/20250129234403.574766-1-jm@ti.com

arm: mach-k3: am62*_init: Probe ESM nodes

2025-02-10T16:30:41Z

On AM62A and AM62P devices, it is possible to route Main ESM error events to MCU ESM. MCU ESM high error output can trigger the reset logic to reset the device. So, for these devices we have Main ESM and MCU ESM nodes in the device tree. Add functions to probe these nodes if CONFIG_ESM_K3 is enabled. Signed-off-by: Santhosh Kumar K Signed-off-by: Judith Mendez

mediatek: mt7981: enable ethernet switch auto-detction

2025-02-10T16:28:31Z

This patch enables switch auto-detction for mt7981 as some new mt7981 boards will use AN8855 ethernet switch. Signed-off-by: Weijie Gao

arch: arm: dts: phyboard-electra-uboot.dtsi: Add bootph props to i2c

2025-02-10T16:28:05Z

Add bootph-all properties to I2C0 nodes to ensure the bus and EEPROM are accessible across all stages. This enables reading the SoM configuration at any point during the boot process. Signed-off-by: Wadim Egorov Tested-by: Daniel Schultz Reviewed-by: Dhruva Gole

mediatek: mt7986: rename pinctrl to pio in mt7986-u-boot.dtsi

2025-02-10T16:26:54Z

The change from pinctrl to pio was missing in mt7986-u-boot.dtsi and will cause build failure. Now fix it. Fixes: f1775996ba9 (mediatek: mt7986: move gpio-controller up and rename pinctrl to pio) Signed-off-by: Weijie Gao

Merge patch series "led: add function naming option from linux"

2025-02-07T17:39:24Z

Heiko Schocher says: In linux we have the option to create the name of a led optionally through the following properties: - function - color - function-enumerator This series adds support for parsing this properties if there is no label property. Link: https://lore.kernel.org/r/20250128135246.74838-1-hs@denx.de [trini: Document name parameter in led.h]

led: add function naming option from linux

2025-02-07T16:53:39Z

in linux we have the option to create the name of a led optionally through the following properties: - function - color - function-enumerator This patch adds support for parsing this properties if there is no label property. The led name is created in led_post_bind() and we need some storage place for it. Currently this patch prevents to use malloc() instead it stores the name in new member : char name[LED_MAX_NAME_SIZE]; of struct led_uc_plat. While at it append led tests for the new feature. Signed-off-by: Heiko Schocher Reviewed-by: Tom Rini

Merge tag 'xilinx-for-v2025.04-rc2' of https://source.denx.de/u-boot/custodians/u-boot-microblaze

2025-02-06T14:09:54Z

AMD/Xilinx changes for v2025.04-rc2 fpga: - Cleanup help - Show xilinx only options on Xilinx devices ospi-versal: - Fix alignment issue - Fix cadence_qspi_flash_reset() prototype zynqmp: - Define usb_pgood_delay - Fix bootseq number versal: - Fix mini_ospi configuration versal2: - Enable OPTEE xilinx: - Enable some flashes - Clean up SYS_MALLOC_F_LEN Kconfig - Some binman fixes - DT updates - Enable mkfwumdata compilation - Enable meminfo command - Switch to LWIP and enable HTTPS

arm: Correct dependency for STATIC_MACH_TYPE

2025-02-05T18:43:48Z

Kconfig should not display the STATIC_MACH_TYPE option when SUPPORT_PASSING_ATAGS is not selected. For example, when using most platforms with menuconfig, it shows the STATIC_MACH_TYPE option causing confusion. As we know, this should not occur when SUPPORT_PASSING_ATAGS is not selected [trini: Reword commit message] Signed-off-by: Liya Huang <1425075683@qq.com>

armv7m: kconfig adds the NVIC option and masks the GIC option when NVIC is selected

2025-02-05T18:43:38Z

ARMv7-M architecture uses NVIC instead of GIC. NVIC is an interrupt controller specially designed for ARM Cortex-M series processors. Signed-off-by: Liya Huang <1425075683@qq.com>