u-boot.git/board/Barix, branch v2014.07

mtd: nand: davinci: add header file for driver definitions

2014-06-19T21:53:58Z

The definitions inside emif_defs.h concern davinci nand driver and should be in it's header. So create header file for davinci nand driver and move definitions from emif_defs.h and nand_defs.h to it. Acked-by: Vitaly Andrianov Signed-off-by: Ivan Khoronzhuk [trini: Fixup more davinci breakage] Signed-off-by: Tom Rini

arm: make _end compiler-generated

2014-02-26T20:18:09Z

This prevents references to _end from generating absolute relocation records. This change is binary invariant for ARM targets. Signed-off-by: Albert ARIBAUD

Merge branch 'iu-boot/master' into 'u-boot-arm/master'

2013-11-09T21:59:47Z

Conflicts: arch/arm/cpu/arm926ejs/mxs/Makefile board/compulab/cm_t35/Makefile board/corscience/tricorder/Makefile board/ppcag/bg0900/Makefile drivers/bootcount/Makefile include/configs/omap4_common.h include/configs/pdnb3.h Makefile conflicts are due to additions/removals of object files on the ARM branch vs KBuild introduction on the main branch. Resolution consists in adjusting the list of object files in the main branch version. This also applies to two files which are not listed as conflicting but had to be modified: board/compulab/common/Makefile board/udoo/Makefile include/configs/omap4_common.h conflicts are due to the OMAP4 conversion to ti_armv7_common.h on the ARM side, and CONFIG_SYS_HZ removal on the main side. Resolution is to convert as this icludes removal of CONFIG_SYS_HZ. include/configs/pdnb3.h is due to a removal on ARM side. Trivial resolution is to remove the file. Note: 'git show' will also list two files just because they are new: include/configs/am335x_igep0033.h include/configs/omap3_igep00x0.h

arm, da85x: update for the ipam390 board

2013-11-01T19:30:51Z

- switch to correct ecc layout used by the RBL enable CONFIG_NAND_6BYTES_OOB_FREE_10BYTES_ECC - update default environment - change A2CR to correct value for UART boot mode - adapt cs3cfg timings for nand - change LED bootmode signalization Signed-off-by: Heiko Schocher Cc: Tom Rini

board: arm: convert makefiles to Kbuild style

2013-11-01T15:42:12Z

Signed-off-by: Masahiro Yamada Cc: Albert ARIBAUD Cc: Andreas Bießmann Cc: Stefano Babic Cc: Prafulla Wadaskar Cc: Minkyu Kang Cc: Vipin Kumar Cc: Tom Warren Cc: Tom Rini

Coding Style cleanup: replace leading SPACEs by TABs

2013-10-14T20:06:54Z

Signed-off-by: Wolfgang Denk [trini: Drop changes for PEP 4 following python tools] Signed-off-by: Tom Rini

arm, da850: add ipam390 board support

2013-08-15T22:38:36Z

add the am1808 based ipam390 board from Barix. - 128MByte, DDR2, synchronous RAM 16bit databus to SDRAM interface - 128MByte, NAND Flash, 8bit databus to the NANDFlash Interface - Ethernet PHY Micrel KSZ8051R via RMII - Console on UART 0 - booting fron nand flash - spl falcon bootmode Signed-off-by: Heiko Schocher Cc: Tom Rini