u-boot.git/board/atmel, branch v2012.10

Merge remote-tracking branch 'u-boot/master'

2012-09-30T21:49:17Z

at91sam9x5: set default EBI I/O drive configuration.

2012-09-13T12:27:28Z

This patch configure at91sam9x5's EBI drive I/O. Without this, When SD card boot, the nand flash read/write are not stable. Which will cause kernel MTD test fail (Since mainline kernel doesn't configure the EBI register). Signed-off-by: Josh Wu Signed-off-by: Andreas Bießmann

avr32: add atngw100mkii board

2012-09-13T11:33:11Z

This patch is derived from an older patch provided by atmel in its buildroot-avr32-v3.0.0.tar.bz2 Signed-off-by: Andreas Bießmann cc: Hans-Christian Egtvedt Acked-by: Hans-Christian Egtvedt

at91: 9x5: change SMC config timing that both works for PMECC & non-PMECC.

2012-09-01T15:06:14Z

Signed-off-by: Josh Wu Tested-by: voice.shen@atmel.com Signed-off-by: Andreas Bießmann

arm:at91-boards: remove console_init_f where unnecessary

2012-09-01T15:06:14Z

A lot of at91 boards have the console_init_f in board_init. This is useless cause it was called before by generic code in lib/board.c. Signed-off-by: Andreas Bießmann cc: Jens Scharsig cc: Stelian Pop cc: Sedji Gaouaou cc: Albin Tonnerre cc: Eric Benard Tested-by: voice.shen@atmel.com Tested-by: voice.shen@atmel.com Acked-by: Jens Scharsig (BuS Elektronik) Tested-by: Jens Scharsig (BuS Elektronik)

at91sam9263ek: remove unnecessary console_init_f

2012-09-01T15:06:14Z

Signed-off-by: Andreas Bießmann cc: Stelian Pop

arm : at91sam9x5 : fix a small bug for NAND

2012-09-01T15:06:13Z

fix a bug: when not boot from NAND, the NAND flash can not be detected. Using this to fix it Signed-off-by: Bo Shen Signed-off-by: Andreas Bießmann

arm : Atmel : add at91sam9x5ek board support

2012-09-01T12:58:14Z

Add at91sam9x5ek board support, this board support the following SoCs AT91SAM9G15, AT91SAM9G25, AT91SAM9G35, AT91SAM9X25, AT91SAM9X35 Using at91sam9x5ek_nandflash to configure for the board Now only supports NAND with software ECC boot up Signed-off-by: Bo Shen [move MAINTAINERS entry to right place] Signed-off-by: Andreas Bießmann

AT91SAM9*: Change kernel address in dataflash to match u-boot's size

2012-07-07T12:07:30Z

On at91sam platforms, u-boot grew larger than the allocated size in dataflash, the layout was: bootstrap 0x00000000 ubootenv 0x00004200 uboot 0x00008400 kernel 0x00042000 fs 0x00252000 u-boot with the defconfig doesn't seem to fit in 0x42000 - 0x8400 = 0x39C00 bytes anymore. Now, the layout is: bootstrap 0x00000000 ubootenv 0x00004200 uboot 0x00008400 kernel 0x00084000 fs 0x00294000 Signed-off-by: Alexandre Belloni Signed-off-by: Andreas Bießmann

Fix: broken boot message at serial line on AT91SAM9263-EK board

2012-07-07T12:07:29Z

Signed-off-by: Jens Scharsig (BuS Elektronik) Signed-off-by: Andreas Bießmann