u-boot.git/board/avionic-design, branch v2016.07

ARM: tegra: use DT bindings for GPIO naming

2016-05-31T16:53:56+00:00

There are currently many places that define the list of all Tegra GPIOs;
the DT binding header and custom Tegra-specific header file gpio.h. Fix
the redundancy by replacing everything with the DT binding header file.

Signed-off-by: Stephen Warren 
Reviewed-by: Simon Glass 
Signed-off-by: Tom Warren

ARM: tegra: move NVIDIA common files to arch/arm/mach-tegra

2015-05-13T16:46:19+00:00

All the Tegra boards borrow the files from board/nvidia/common/
directory, i.e., board/nvidia/common/* are not vendor-common files,
but SoC-common files.

Move NVIDIA common files to arch/arm/mach-tegra/ to clean up
Makefiles.

As arch/arm/mach-tegra/board.c already exists, this commit renames
board/nvidia/common/board.c to arch/arm/mach-tegra/board2.c,
expecting they will be consolidated as a second step.

Signed-off-by: Masahiro Yamada 
Acked-by: Marcel Ziswiler 
Cc: Stephen Warren 
Cc: Tom Warren 
Cc: Simon Glass 
Acked-by: Simon Glass 
Signed-off-by: Tom Warren

dm: i2c: Provide an offset length parameter where needed

2015-01-30T00:09:53+00:00

Rather than assuming that the chip offset length is 1, allow it to be
provided. This allows chips that don't use the default offset length to
be used (at present they are only supported by the command line 'i2c'
command which sets the offset length explicitly).

Signed-off-by: Simon Glass 
Acked-by: Heiko Schocher

dm: i2c: Rename driver model I2C functions to permit compatibility

2015-01-30T00:09:53+00:00

Add a dm_ prefix to driver model I2C functions so that we can keep the old
ones around.

This is a little unfortunate, but on reflection it is too difficult to
change the API. We can undo this rename when most boards and drivers are
converted to use driver model for I2C.

Signed-off-by: Simon Glass

dm: i2c: tegra: Convert to driver model

2014-12-11T20:18:44+00:00

This converts all Tegra boards over to use driver model for I2C. The driver
is adjusted to use driver model and the following obsolete CONFIGs are
removed:

   - CONFIG_SYS_I2C_INIT_BOARD
   - CONFIG_I2C_MULTI_BUS
   - CONFIG_SYS_MAX_I2C_BUS
   - CONFIG_SYS_I2C_SPEED
   - CONFIG_SYS_I2C

This has been tested on:
- trimslice (no I2C)
- beaver
- Jetson-TK1

It has not been tested on Tegra 114 as I don't have that board.

Acked-by: Heiko Schocher 
Signed-off-by: Simon Glass

kconfig: remove redundant "string" type in arch and board Kconfigs

2014-09-13T20:43:55+00:00

Now the types of CONFIG_SYS_{ARCH, CPU, SOC, VENDOR, BOARD, CONFIG_NAME}
are specified in arch/Kconfig.

We can delete the ones in arch and board Kconfig files.

This commit can be easily reproduced by the following command:

find . -name Kconfig -a ! -path ./arch/Kconfig | xargs sed -i -e '
/config[[:space:]]SYS_\(ARCH\|CPU\|SOC\|\VENDOR\|BOARD\|CONFIG_NAME\)/ {
    N
    s/\n[[:space:]]*string//
}
'

Signed-off-by: Masahiro Yamada

tegra: kconfig: move board select menu and common settings

2014-08-31T01:19:32+00:00

Becuase the board select menu in arch/arm/Kconfig is too big,
move the Tegra board select menu to tegra/Kconfig.

Insert the Tegra SoC select menu between the arch select and the
board select.

 Architecture select
 |-- Tegra Platform (Tegra)
     |- Tegra SoC select (Tegra20 / 30 / 114 / 124)
        |- Board select

Consolidate also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="tegra*") and always "select" CONFIG_SPL as follows:

  config TEGRA
          bool
          select SPL

Signed-off-by: Masahiro Yamada 
Acked-by: Stephen Warren 
Cc: Tom Warren

Add board MAINTAINERS files

2014-07-30T12:48:06+00:00

We have switched to Kconfig and the boards.cfg file is going to
be removed. We have to retrieve the board status and maintainers
information from it.

The MAINTAINERS format as in Linux Kernel would be nice
because we can crib the scripts/get_maintainer.pl script.

After some discussion, we chose to put a MAINTAINERS file under each
board directory, not the top-level one because we want to collect
relevant information for a board into a single place.

TODO:
Modify get_maintainer.pl to scan multiple MAINTAINERS files.

Signed-off-by: Masahiro Yamada 
Suggested-by: Tom Rini 
Acked-by: Simon Glass

kconfig: add board Kconfig and defconfig files

2014-07-30T12:48:01+00:00

This commit adds:
 - arch/${ARCH}/Kconfig
    provide a menu to select target boards
 - board/${VENDOR}/${BOARD}/Kconfig or board/${BOARD}/Kconfig
    set CONFIG macros to the appropriate values for each board
 - configs/${TARGET_BOARD}_defconfig
    default setting of each board

(This commit was automatically generated by a conversion script
based on boards.cfg)

In Linux Kernel, defconfig files are located under
arch/${ARCH}/configs/ directory.
It works in Linux Kernel since ARCH is always given from the
command line for cross compile.

But in U-Boot, ARCH is not given from the command line.
Which means we cannot know ARCH until the board configuration is done.
That is why all the "*_defconfig" files should be gathered into a
single directory ./configs/.

Signed-off-by: Masahiro Yamada 
Acked-by: Simon Glass

ARM: tegra: Tegra30 pinmux cleanup

2014-04-17T15:41:05+00:00

This renames all the pinmux pins, drive groups, and functions so they
have a prefix which matches the type name. These lists are also auto-
generated using scripts that were also used to generate the kernel
pinctrl drivers. This ensures that the lists are consistent between the
two.

The entries in tegra30_pingroups[] are all updated to remove the columns
which are no longer used.

All affected code is updated to match.

This introduces a few changes to pin/group/function naming and the set of
available functions for each pin. The new values now exactly match the
TRM; the chip documentation. I adjusted one entry in
pinmux-config-cardhu.h due to this.

Signed-off-by: Stephen Warren 
Acked-by: Simon Glass 
Signed-off-by: Tom Warren