u-boot.git/board/compulab, branch v2015.10

mx6: remove SYS_SOC from board Kconfig

2015-09-13T08:37:29Z

Remove duplicated SYS_SOC Kconfig entry from board Kconfig, because we have this entry in arch/arm/cpu/armv7/mx6/Kconfig. Signed-off-by: Peng Fan Cc: Stefano Babic Cc: Heiko Schocher Cc: Christian Gmeiner Cc: Stefan Roese Cc: Troy Kisky Cc: Nikita Kiryanov Cc: "Eric Bénard" Cc: Fabio Estevam Cc: Tim Harvey Cc: Marek Vasut Cc: Markus Niebel Cc: Otavio Salvador Acked-by: Stefan Roese Acked-by: Marek Vasut Acked-by: Christian Gmeiner Acked-by: Markus Niebel Acked-by: Troy Kisky Acked-by: Igor Grinberg

arm: mx6: cm-fx6: modify device tree for old revisions of utilite

2015-09-13T08:36:20Z

Old revisions of Utilite (a miniature PC based on cm-fx6) do not have a card detect for mmc, and thus the kernel needs to be told that there's a persistent storage on usdhc3 to force it to probe the mmc card. Check the baseboard revision and modify the device tree accordingly if needed. Cc: Stefano Babic Cc: Igor Grinberg Signed-off-by: Nikita Kiryanov

compulab: eeprom: add support for obtaining product name

2015-09-13T08:36:01Z

Introduce cl_eeprom_get_product_name() for obtaining product name from the eeprom. Cc: Stefano Babic Cc: Igor Grinberg Signed-off-by: Nikita Kiryanov

compulab: eeprom: propagate error value in read_mac_addr()

2015-09-13T08:35:43Z

cl_eeprom_read_mac_addr() doesn't differentiate between success case and inability to access eeprom. Fix this by propagating the return value of cl_eeprom_setup(). Cc: Stefano Babic Cc: Igor Grinberg Signed-off-by: Nikita Kiryanov Acked-by: Igor Grinberg

compulab: eeprom: select i2c bus when querying for board rev

2015-09-13T08:35:06Z

Add support for selecting which eeprom is queried for board revision by extending cl_eeprom_get_board_rev() to accept an i2c bus number. Cc: Stefano Babic Cc: Igor Grinberg Acked-by: Igor Grinberg Signed-off-by: Nikita Kiryanov

omap3: cm-t3517: fix MMC1 pinmux

2015-09-11T21:15:33Z

Fix MMC1 pinmux setup, thus enable SD/MMC card support with CM-T3517. Signed-off-by: Dmitry Lifshitz Acked-by: Igor Grinberg

arm: mx6: cm-fx6: print PCB revision

2015-09-02T13:38:16Z

Print board revision for cm-fx6. Cc: Stefano Babic Cc: Igor Grinberg Signed-off-by: Nikita Kiryanov Acked-by: Igor Grinberg

arm: mx6: cm-fx6: force host mode on usb controller

2015-09-02T13:38:16Z

On some CM-FX6 modules U-Boot attempts to configure the usb0 controller in device mode, which renders it unavailable: USB0: Port not available. and also causes usb stop to report an error EHCI failed to shut down host controller. This happens mostly on MX6 Dual based modules, and is caused by the USBPHY_CTRL register reporting USBPHY_CTRL_OTG_ID to be 1, even when it is pulled down. Since we do not support device mode in cm-fx6 u-boot, force all controllers to be configured as hosts. Cc: Stefano Babic Cc: Igor Grinberg Signed-off-by: Nikita Kiryanov Acked-by: Igor Grinberg

arm: am437x: Introduce new board cm-t43

2015-08-13T00:48:05Z

Add initial support for CM-T43, an AM437x based SoM. This support includes: serial, MMC/eMMC, NAND, USB, ETH, I2C, GPIO, DRAM detection. Cc: Tom Rini Cc: Albert Aribaud Cc: Igor Grinberg Signed-off-by: Nikita Kiryanov

usb: musb-new: CONFIG_MUSB prefix replacement with CONFIG_USB_MUSB

2015-08-05T15:20:34Z

USB-related options are usually prefixed with CONFIG_USB and platform-specific adaptation for the MUSB controller already have a CONFIG_USB_MUSB prefix, so this switches all MUSB-related options to a CONFIG_USB_MUSB prefix, for consistency. Signed-off-by: Paul Kocialkowski