u-boot.git/board/compulab, branch v2016.09-rc2

ARM: board: cm_fx6: fixup mtd partitions in the fdt

2016-07-19T17:52:13Z

The cm-fx6 module has an on-board st,m25p compatible spi flash chip used for U-Boot (binary & environment). Overwrite the partitions in the device tree by the partition table provided in the mtdparts environment variable, if it is set. This allows to specify a kernel independent partitioning in the environment and provides a convient way for the user to adapt the partition table. Signed-off-by: Christopher Spinrath Acked-by: Igor Grinberg

ARM: board: cm-fx6: fix mmc for old revisions of utilite

2016-07-12T15:58:48Z

Old revisions of Utilite (based on cm-fx6) do not have a dedicated card detect pin. But the card is removable by the user and card detection can be realized with polling (e.g. supported by Linux). Add the broken-cd property to the mmc device tree instead of the non-removable property to make card detection possible if polling is supported. Signed-off-by: Christopher Spinrath Acked-by: Nikita Kiryanov

compulab: add support for layout aware eeprom commands

2016-05-20T21:02:07Z

Add layout definitions and implement functions for field printing/updating, layout detection, layout assignment, and layout parsing. Cc: Igor Grinberg Cc: Tom Rini Signed-off-by: Nikita Kiryanov

omap-common: Rename set_muxconf_regs_essential to set_muxconf_regs

2016-03-15T19:12:06Z

There is no distinction between essential and non-essential mux configuration, so it doesn't make sense to have an "essential" prefix. Signed-off-by: Paul Kocialkowski

arm: am437x: cm-t43: set MPU and CORE voltages on boot

2016-02-24T23:44:09Z

During boot, U-Boot raises the CPU frequency but the CORE and MPU regulators are not updated. This is not a problem in cold boot since the default values that the pmic outputs are correct, but if Linux were to switch the module to a low power OPP, the new voltage values will be retained after a reboot and the module will likely hang once U-Boot raises the CPU frequency back up. Set both CORE and MPU regulators to to 1.1V on boot. Cc: Tom Rini Cc: Albert Aribaud Cc: Igor Grinberg Signed-off-by: Nikita Kiryanov Reviewed-by: Tom Rini

arm: am437x: cm-t43: get rid of enable_vtt_regulator()

2016-02-24T23:44:08Z

CM-T43 does not have a vtt regulator. Remove the function that's supposed to enable it. Cc: Tom Rini Cc: Albert Aribaud Cc: Igor Grinberg Signed-off-by: Nikita Kiryanov Reviewed-by: Tom Rini

arm: am437x: cm-t43: set tps fseal bit

2016-02-24T23:44:08Z

Set TPS65218 FSEAL bit to 1 so that RTC could be powered using on-board 3V battery. This is necessary so that time and date will survive reboots and power offs. Cc: Tom Rini Cc: Albert Aribaud Cc: Igor Grinberg Signed-off-by: Nikita Kiryanov Reviewed-by: Tom Rini

arm: am437x: cm-t43: split board file

2016-02-24T23:44:06Z

Simplify the board file by splitting it to spl portion and u-boot portion. Some unnecessary includes were identified and removed. No functional changes. Cc: Tom Rini Cc: Albert Aribaud Cc: Igor Grinberg Signed-off-by: Nikita Kiryanov Reviewed-by: Tom Rini

dm: tegra: net: Convert tegra boards to driver model for Ethernet

2016-01-12T17:19:09Z

Adjust all Tegra boards to use driver model for Ethernet, now that the required drivers are converted. Signed-off-by: Simon Glass Reviewed-by: Bin Meng Acked-by: Joe Hershberger

omap3: cm-t3517: add board specific get_board_rev()

2015-11-18T19:50:06Z

CM-T3517 has several HW revisions. Add board specific get_board_rev() callback to retrieve revision number. Signed-off-by: Dmitry Lifshitz Reviewed-by: Igor Grinberg