u-boot.git/board/compulab, branch v2018.05

SPDX: Convert all of our single license tags to Linux Kernel style

2018-05-07T13:34:12+00:00

When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini

Remove unnecessary instances of DECLARE_GLOBAL_DATA_PTR

2018-04-27T18:54:48+00:00

We have a large number of places where while we historically referenced
gd in the code we no longer do, as well as cases where the code added
that line "just in case" during development and never dropped it.

Signed-off-by: Tom Rini

net: Move enetaddr env access code to env config instead of net config

2018-04-09T03:00:58+00:00

In order that we can use eth_env_* even when CONFIG_NET isn't set, move
these functions to environment code from net code.

This fixes failures such as:

  board/ti/am335x/built-in.o: In function `board_late_init':
  board/ti/am335x/board.c:752: undefined reference to `eth_env_set_enetaddr'
  u-boot/board/ti/am335x/board.c:766: undefined reference to `eth_env_set_enetaddr'

which caters for use cases such as:

commit f411b5cca48f ("board: am335x: Always set eth/eth1addr environment
variable")

when Ethernet is required in Linux, but not U-Boot.

Signed-off-by: Alex Kiernan

Revert "mx6: ddr: Allow changing REFSEL and REFR fields"

2018-02-22T13:30:53+00:00

This reverts commit edf0093732225c2fd0791c3864e9a3eef1f92f19 for
cm_fx6 iMX.6 Solo module as it causes frequent (around 10 percent of
power cycles) board's hangs.

These hangs happen in SPL when BSS is being initialized in SDRAM -
it appear that variables from BSS contain trash values which lead to board
hangs. Looks like that SDRAM doesn't yet finish initialization in these
cases.

Signed-off-by: Maxim Yu. Osipov 
Reviewed-by: Stefano Babic

usb: host: xhci-omap: Remove redundant board_usb_init and board_usb_cleanup functions

2018-02-15T12:44:30+00:00

board_usb_init()/_cleanup() should be in board files and don't have
a place in the xhci-omap driver. Weak versions for
board_usb_init()/_cleanup() already exist in common/usb.c
(for host mode) and drivers/usb/gadget/g_dnl.c (for gadget mode).

Therefore, remove init and cleanup functions from xhci-omap and
implement them in the board files.

Signed-off-by: Faiz Abbas 
Reviewed-by: Marek Vasut 
Reviewed-by: Bin Meng

ARM: imx: cm_fx6: export board and soc info to env

2018-01-12T13:28:04+00:00

Like many other i.MX6 based boards, there are multiple variants of
the cm-fx6 module featuring different SoC variants. Furthermore, the
module can be paired with multiple baseboards.

At the same time modern distribution like Fedora require U-Boot to
select a proper devicetree which depends on the SoC variant and the
baseboard.

Thus, export the SoC variant and the actual board to the environment
following the conventions of other i.MX6 devices (e.g. the NXP boards)
such that the environment can select a devicetree file to load.

For now, we only know for sure that the cm-fx6 module and the SB-fx6m
baseboard amount to a Utilite Computer variant (depending on the SoC).
Further combinations may be added in the future; e.g. CompuLab's
evaluation board once someone can verify the identification string
stored in its eeprom.

Signed-off-by: Christopher Spinrath 
Reviewed-by: Stefano Babic

ARM: imx: cm_fx6: remove esdhc init code from board file

2017-12-29T10:18:59+00:00

Commit 5248930ebf48 ("dm: imx: cm_fx6: Enable more driver model support")
enabled driver model support for MMC. Remove the old mmc init code, which
is no longer used, from the board file.

Signed-off-by: Christopher Spinrath 
Reviewed-by: Fabio Estevam 
Reviewed-by: Simon Glass

ARM: imx: cm_fx6: remove sata init code from board file

2017-12-29T10:18:59+00:00

Commit 5248930ebf48 ("dm: imx: cm_fx6: Enable more driver model support")
enabled driver model support for AHCI. Remove the old, now unused, sata
init code from the board file.

Signed-off-by: Christopher Spinrath 
Reviewed-by: Fabio Estevam 
Reviewed-by: Simon Glass

usb: hub: identify the hub-device to usb_hub_reset_devices

2017-11-26T01:22:36+00:00

When usb_hub_reset_devices is called, it should be passed both an
indicator which hub it should operate on and what port number (local
to that hub) should be reset.

Previously, the usb_hub.c code did not include such context and
always started resets from port number 1, performing multiple
reset-requests for the same devices:

       /*
        * Reset any devices that may be in a bad state when applying
        * the power.  This is a __weak function.  Resetting of the devices
        * should occur in the board file of the device.
        */
       for (i = 0; i < dev->maxchild; i++)
              usb_hub_reset_devices(i + 1);

This adds an additional 'hub' parameter to usb_hub_reset_devices
that provides the context to fully qualify the port-number in.

Existing implementations are changed to accept and ignore the new
parameter.

Signed-off-by: Philipp Tomsich 
Tested-by: Jakob Unterwurzacher

net: Add SMC911X driver to Kconfig, convert

2017-10-21T01:40:26+00:00

We add the various SMC91XX symbols to drivers/net/Kconfig and then this
converts the following to Kconfig:
   CONFIG_SMC911X
   CONFIG_SMC911X_BASE
   CONFIG_SMC911X_16_BIT
   CONFIG_SMC911X_32_BIT

Signed-off-by: Adam Ford 
[trini: Apply to the rest of the tree, re-squash old and new patch]
Signed-off-by: Tom Rini