u-boot.git/board/compulab, branch v2018.05-rc2

net: Move enetaddr env access code to env config instead of net config

2018-04-09T03:00:58Z

In order that we can use eth_env_* even when CONFIG_NET isn't set, move these functions to environment code from net code. This fixes failures such as: board/ti/am335x/built-in.o: In function `board_late_init': board/ti/am335x/board.c:752: undefined reference to `eth_env_set_enetaddr' u-boot/board/ti/am335x/board.c:766: undefined reference to `eth_env_set_enetaddr' which caters for use cases such as: commit f411b5cca48f ("board: am335x: Always set eth/eth1addr environment variable") when Ethernet is required in Linux, but not U-Boot. Signed-off-by: Alex Kiernan

Revert "mx6: ddr: Allow changing REFSEL and REFR fields"

2018-02-22T13:30:53Z

This reverts commit edf0093732225c2fd0791c3864e9a3eef1f92f19 for cm_fx6 iMX.6 Solo module as it causes frequent (around 10 percent of power cycles) board's hangs. These hangs happen in SPL when BSS is being initialized in SDRAM - it appear that variables from BSS contain trash values which lead to board hangs. Looks like that SDRAM doesn't yet finish initialization in these cases. Signed-off-by: Maxim Yu. Osipov Reviewed-by: Stefano Babic

usb: host: xhci-omap: Remove redundant board_usb_init and board_usb_cleanup functions

2018-02-15T12:44:30Z

board_usb_init()/_cleanup() should be in board files and don't have a place in the xhci-omap driver. Weak versions for board_usb_init()/_cleanup() already exist in common/usb.c (for host mode) and drivers/usb/gadget/g_dnl.c (for gadget mode). Therefore, remove init and cleanup functions from xhci-omap and implement them in the board files. Signed-off-by: Faiz Abbas Reviewed-by: Marek Vasut Reviewed-by: Bin Meng

ARM: imx: cm_fx6: export board and soc info to env

2018-01-12T13:28:04Z

Like many other i.MX6 based boards, there are multiple variants of the cm-fx6 module featuring different SoC variants. Furthermore, the module can be paired with multiple baseboards. At the same time modern distribution like Fedora require U-Boot to select a proper devicetree which depends on the SoC variant and the baseboard. Thus, export the SoC variant and the actual board to the environment following the conventions of other i.MX6 devices (e.g. the NXP boards) such that the environment can select a devicetree file to load. For now, we only know for sure that the cm-fx6 module and the SB-fx6m baseboard amount to a Utilite Computer variant (depending on the SoC). Further combinations may be added in the future; e.g. CompuLab's evaluation board once someone can verify the identification string stored in its eeprom. Signed-off-by: Christopher Spinrath Reviewed-by: Stefano Babic

ARM: imx: cm_fx6: remove esdhc init code from board file

2017-12-29T10:18:59Z

Commit 5248930ebf48 ("dm: imx: cm_fx6: Enable more driver model support") enabled driver model support for MMC. Remove the old mmc init code, which is no longer used, from the board file. Signed-off-by: Christopher Spinrath Reviewed-by: Fabio Estevam Reviewed-by: Simon Glass

ARM: imx: cm_fx6: remove sata init code from board file

2017-12-29T10:18:59Z

Commit 5248930ebf48 ("dm: imx: cm_fx6: Enable more driver model support") enabled driver model support for AHCI. Remove the old, now unused, sata init code from the board file. Signed-off-by: Christopher Spinrath Reviewed-by: Fabio Estevam Reviewed-by: Simon Glass

usb: hub: identify the hub-device to usb_hub_reset_devices

2017-11-26T01:22:36Z

When usb_hub_reset_devices is called, it should be passed both an indicator which hub it should operate on and what port number (local to that hub) should be reset. Previously, the usb_hub.c code did not include such context and always started resets from port number 1, performing multiple reset-requests for the same devices: /* * Reset any devices that may be in a bad state when applying * the power. This is a __weak function. Resetting of the devices * should occur in the board file of the device. */ for (i = 0; i < dev->maxchild; i++) usb_hub_reset_devices(i + 1); This adds an additional 'hub' parameter to usb_hub_reset_devices that provides the context to fully qualify the port-number in. Existing implementations are changed to accept and ignore the new parameter. Signed-off-by: Philipp Tomsich Tested-by: Jakob Unterwurzacher

net: Add SMC911X driver to Kconfig, convert

2017-10-21T01:40:26Z

We add the various SMC91XX symbols to drivers/net/Kconfig and then this converts the following to Kconfig: CONFIG_SMC911X CONFIG_SMC911X_BASE CONFIG_SMC911X_16_BIT CONFIG_SMC911X_32_BIT Signed-off-by: Adam Ford [trini: Apply to the rest of the tree, re-squash old and new patch] Signed-off-by: Tom Rini

arm: imx7d: add support for Compulab cl-som-imx7

2017-10-12T15:31:16Z

Add initial support for Compulab cl-som-imx7 SoM. The initial support includes: - MMC - eMMC - SPI flash - I2C - FEC - USB - Serial console Signed-off-by: Ilya Ledvich

imx6: drop duplicated bss memset and board_init_r() call

2017-09-18T15:15:28Z

bss section is cleared in crt0.S. board_init_r() is also entered from crt0 code. Signed-off-by: Anatolij Gustschin Cc: Christian Gmeiner Cc: Nikita Kiryanov Cc: Jagan Teki Cc: Tim Harvey Cc: Marek Vasut Cc: Lukasz Majewski Cc: Fabio Estevam Reviewed-by: Lukasz Majewski Reviewed-by: Christian Gmeiner Reviewed-by: Fabio Estevam