u-boot.git/board/congatec, branch v2016.07

x86: baytrail: Add .gitignore for ACPI enabled boards

2016-05-23T07:18:00+00:00

Let git ignore dsdt.aml, dsdt.asl.tmp and dsdt.c files.

Signed-off-by: Bin Meng 
Reviewed-by: Stefan Roese 
Tested-by: Stefan Roese 
Reviewed-by: Simon Glass

x86: baytrail: Enable ACPI table generation for all boards

2016-05-23T07:18:00+00:00

Enable ACPI table generation by creating a DSDT table for all baytrail
boards: conga-qeval20-qa3-e3845, bayleybay and minnowmax.

Signed-off-by: Bin Meng 
Reviewed-by: Stefan Roese 
Tested-by: Stefan Roese 
Reviewed-by: Simon Glass

x86: Add congatec conga-QA3/E3845-4G (Bay Trail) support

2016-03-17T02:27:27+00:00

This patch adds support for the congatec conga-QA3/E3845-4G eMMC8 SoM,
installed on the congatec Qseven 2.0 evaluation carrier board
(conga-QEVAL).

Its port is very similar to the MinnowboardMAX port and also uses
the Intel FSP as described in doc/README.x86.

Currently supported are the following interfaces / devices:
- UART (via Winbond legacy SuperIO chip on carrier board)
- Ethernet (PCIe Intel I210 / E1000)
- SPI including SPI NOR as boot-device
- USB 2.0
- SATA via U-Boot SCSI IF
- eMMC
- Video (HDMI output @ 800x600)
- PCIe

Not supported yet is:
- I2C
- USB 3.0

Signed-off-by: Stefan Roese 
Cc: Simon Glass 
Cc: Bin Meng 
Reviewed-by: Bin Meng

Use correct spelling of "U-Boot"

2016-02-06T11:00:59+00:00

Correct spelling of "U-Boot" shall be used in all written text
(documentation, comments in source files etc.).

Signed-off-by: Bin Meng 
Reviewed-by: Heiko Schocher 
Reviewed-by: Simon Glass 
Reviewed-by: Minkyu Kang

cgtqmx6eval: README: Fix parameter of 'sf write' command

2016-01-10T09:51:43+00:00

'sf command' should receive the length in sector boundaries, so fix it
accordingly.

Also, show the steps to set the server and board IP addresses for
making the steps clearer.

Signed-off-by: Otavio Salvador 
Reviewed-by: Fabio Estevam

cgtqmx6eval: fix pad configuration for SPI bus

2016-01-03T14:28:56+00:00

Use the macro SETUP_IOMUX_PAD(...) rather than imx_iomux_v3_setup_multiple_pads(...) in order to setup
the pin configuration for ECSPI1.

ARRAY_SIZE(pads) provides the wrong size for imx_iomux_v3_setup_multiple_pads(pads, ARRAY_SIZE(pads)) in
case of MX6QDL. In the particular case, the content of GPR12 is overwritten and the IPG/AHB/ATB/ATP clocks
are deactivated. Therefore, the connection to the system via JTAG is not possible anymore. Furthermore,
kernel version 3.0.35 hangs during bootprocess in the function etm_init().

Signed-off-by: Michael Schanz 
Acked-by: Otavio Salvador

cgtqmx6eval: Fix defconfig name

2015-12-07T13:48:02+00:00

After the conversion to SPL the defconfig was renamed, so adjust it.

Signed-off-by: Otavio Salvador

cgtqmx6eval: Add SPL support

2015-11-25T08:41:29+00:00

Congatec has several MX6 boards based on quad, dual, dual-lite and solo.

Add SPL support so that all the variants can be supported

Signed-off-by: Otavio Salvador 
Reviewed-by: Fabio Estevam

cgtqmx6eval: Add SPI NOR flash support

2015-11-25T08:37:58+00:00

Add SPI NOR support:

=> sf probe
SF: Detected SST25VF032B with page size 256 Bytes, erase size 4 KiB, total 4 MiB

Signed-off-by: Otavio Salvador 
Reviewed-by: Fabio Estevam

cgtqmx6eval: Add a maintainer entry

2015-09-20T09:10:26+00:00

Add me as the board maintainer and move the status to 'Maintained'.

Signed-off-by: Otavio Salvador