The YModem support in SPL was never really used on this device,
the SDP support is much more convenient on i.MX8M Mini based
hardware. Replace the YModem support with SDP support.

The SDP can be utilized by forcing the board into SDP boot mode
by grounding test point right next to silkscreen label U30, and
then by using mfgtools 'uuu -brun spl flash.bin' once the device
enumerates on host system USB bus. The SDP capable USB port is
available on the USB micro-B port on the base board.

Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>

In case gpio_request_list_by_name_nodev() in board dmo_get_memcfg()
returns error code, pick a safe default DRAM configuration instead
of bailing out with some sort of hang() or panic(). The BIT(2)|BIT(0)
strap option is the lowest known option of 2 GiB , use that.

Signed-off-by: Marek Vasut <marex@denx.de>

Use the new symbol to refer to any 'SPL' build, including TPL and VPL

Signed-off-by: Simon Glass <sjg@chromium.org>

The Data Modul i.MX8M Plus eDM SBC does have USB gadget capable port
accessible via USB A-A cable plugged into the bottom USB 3.0 port.
Use USB SDPS as the fallback boot device, so USB SDPS loading can
be performed using e.g. uuu tool.

Signed-off-by: Marek Vasut <marex@denx.de>

As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.

Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>

When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.

This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.

Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>

Remove <common.h> from this board vendor directory and when needed
add missing include files directly.

Signed-off-by: Tom Rini <trini@konsulko.com>

The CONFIG_SPL_BOARD_INIT lets SPL common code call spl_board_init()
during the SPL start up. On this particular system, spl_board_init()
is used to reconfigure GIC clock parent to PLL2 500M, which is the
configuration expected by the Linux kernel. Enable SPL_BOARD_INIT
and fill in the GIC clock configuration code.

Set GIC clock to 500 MHz for OD VDD_SOC. Kernel driver does not
allow to change it. Should set the clock after PMIC setting done.
Default is 400 MHz (system_pll1_800m with div = 2) set by ROM for
ND VDD_SOC.

Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>

Implement fdtdec_board_setup() auto-detection of ethernet PHY.
This uses properties of the hardware and pull resistor placement.

If GPIO1_16 RGMII_MDC is HIGH, then R530 (MX8MM eDM SBC) or
R390 (MX8MP eDM SBC) is populated. R530 or R390 is populated
only on boards with AR8031 PHY.

If GPIO1_16 RGMII_MDC is LOW, then the in-SoM pull down is the
dominant pull resistor. This is the case on boards with BCM54213PE
PHY.

In case AR8031 PHY is populated, the PHY MDIO address is 0, in
case BCM54213PE PHY is populated, the PHY MDIO address is 1, the
fdtdec_board_setup() is used to patch the correct address into
the U-Boot control DT.

Enable broadcom PHY support to support both PHYs.

Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>

These files include <common.h> twice. Start by removing the second
inclusion of the file.

Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>