u-boot.git/board/davinci, branch v2013.01

common: Add .u_boot_list into all linker files

2012-10-22T15:29:42Z

Add section for the linker-generated lists into all possible linker files, so that everyone can easily use these lists. This is mostly a mechanical adjustment. Signed-off-by: Marek Vasut Cc: Joe Hershberger Cc: Mike Frysinger

davinci: ea20: the console is always set to the serial line

2012-10-01T17:02:13Z

Do not allow to overwrite it when video is enabled. Signed-off-by: Bastian Ruppert CC: Tom Rini Acked-by: Stefano Babic

davinci: ea20: reorganisation LCD startup

2012-10-01T17:02:12Z

Signed-off-by: Bastian Ruppert CC: Tom Rini Acked-by: Stefano Babic

da850: Add README.da850

2012-09-27T18:20:27Z

This file documents when to build for da850evm and when to build for da850_am18xxevm. It also documents how to write the u-boot.ais file to persistent storage (such as SPI), in some cases as well as how to write a recovery image. Signed-off-by: Tom Rini Acked-by: Christian Riesch Acked-by: Prabhakar Lad

da8xx/hawkboard: Add support for ohci host controller

2012-09-01T12:58:19Z

Also enable the ohci port on hawkboard. These additions result in an increased u-boot size -- adjust the same accordingly in the board's config. Move the usb header for da8xx platforms under arch-davinci. Signed-off-by: Sughosh Ganu

da850/omap-l138: Fix NAND flash timings

2012-09-01T12:58:09Z

Though Commit id a3f88293ddd13facd734769c1664d35ab4ed681f (da850evm: setup the NAND flash timings) has configured the AEMIF timings, they are not exactly in sync with the timings used in Linux. Linux is configuring the timing register as 0x08222204, where as currently it configured to 0x00100084 in U-Boot. This issue was found out when support for NAND SPL is added in U-Boot. Without this patch U-Boot does not come up with SPL. Tested-by: Christian Riesch Signed-off-by: Lad, Prabhakar Signed-off-by: Rajashekhara, Sudhakar Signed-off-by: Hadli, Manjunath

da850/omap-l138: modifications for Logic PD Rev.3 AM18xx EVM

2012-09-01T12:58:09Z

AHCLKR/UART1_RTS/GP0[11] pin needs to be configured for MMC and NOR to work on DA850/OMAP-L138 Rev.3 EVM. When GP0[11] is low, the SD0 interface will not work, but NOR flash will. When GP0[11] is high, SD0 will work but NOR flash will not. Tested-by: Christian Riesch Signed-off-by: Rajashekhara, Sudhakar Signed-off-by: Lad, Prabhakar Signed-off-by: Hadli, Manjunath

da850/omap-l138: Add MMC support for DA850/OMAP-L138

2012-09-01T12:58:09Z

This patch adds support for MMC/SD on DA850/OMAP-L138. Tested-by: Christian Riesch Signed-off-by: Lad, Prabhakar Signed-off-by: Rajashekhara, Sudhakar Signed-off-by: Hadli, Manjunath

hawkboard/omapl-138: Add support for generating ais image for hawkboard

2012-09-01T12:58:08Z

Parameters used for configuring certain SoC peripherals are parsed from the cfg file and appended as part of the ais image's header. The u-boot-spl.ais generated is flashed separately to the nand, so do not delete the file after generation of u-boot.ais. Signed-off-by: Sughosh Ganu

doc: cleanup - move board READMEs into respective board directories

2012-07-29T13:42:02Z

Also drop a few files referring to no longer / not yet supported boards. Signed-off-by: Wolfgang Denk Cc: Prafulla Wadaskar Cc: Stefan Roese Cc: Kim Phillips Cc: Andy Fleming Cc: Jason Jin Cc: Stefano Babic Cc: Daniel Schwierzeck Acked-by: Stefano Babic Acked-by: Daniel Schwierzeck