u-boot.git/board/dhelectronics, branch v2019.10

env: Drop environment.h header file where not needed

2019-08-11T20:43:41Z

This header file is now only used by files that access internal environment features. Drop it from various places where it is not needed. Acked-by: Joe Hershberger Signed-off-by: Simon Glass

env: Move env_set() to env.h

2019-08-11T20:43:41Z

Move env_set() over to the new header file. Acked-by: Joe Hershberger Signed-off-by: Simon Glass

ARM: imx6: DHCOM i.MX6 PDK: Switch to DM for I2C

2019-07-19T18:32:24Z

This patch enables DM I2C for DHCOM i.MX6 PDK2 boards and removes non DM I2C code. The I2C EEPROM with ethaddr (MAC) is defined in the device tree. Use UCLASS_I2C_EEPROM to find the device by fixed hardware path and read the ethaddr. Tested with DHCOM i.MX6dl and DHCOM i.MX6q. Signed-off-by: Ludwig Zenz Reviewed-by: Marek Vasut

ARM: imx6: DHCOM i.MX6 PDK: enable pad pull ups of SS lines of spi used for boot

2019-07-19T18:32:24Z

It turned out that after a reset the boot process from the spi bootflash is disturbed by other spi slave devices connected to DHCOM SPI1, which uses the same spi interface with a different SS line. Therefore the pad pull ups are enabled. Signed-off-by: Ludwig Zenz

ARM: imx6: DHCOM i.MX6 PDK: config SPL to load U-Boot fitImage with mulitple DTs

2019-07-19T18:32:24Z

Configure fitImage for U-Boot with a device tree for imx6 quad/dual and duallite/solo. This enables to support the imx6 derivates quad/dual/duallite/solo with a single binary. Signed-off-by: Ludwig Zenz Reviewed-by: Marek Vasut

ARM: imx: dh-imx6: Enable DM regulator

2019-07-19T18:14:50Z

Enable DM support for regulators and fixed regulator driver and convert USB Vbus control over to the regulators defined in DT. Signed-off-by: Marek Vasut Cc: Ludwig Zenz Cc: Stefano Babic Tested-by: Ludwig Zenz

Convert to use fsl_esdhc_imx for i.MX platforms

2019-06-23T06:18:34Z

Converted to use fsl_esdhc_imx for i.MX platforms. Signed-off-by: Yangbo Lu Tested-by: Steffen Dirkwinkel Reviewed-by: Peng Fan Reviewed-by: Lukasz Majewski Reviewed-by: Martyn Welch Acked-by: Jason Liu

ARM: imx: dh-imx6: Convert SPI support to DM

2019-06-11T08:42:48Z

Enable DM SPI and SF support on DHCOM iMX6 PDK2. Convert board code to match the DM support. Signed-off-by: Marek Vasut Cc: Fabio Estevam Cc: Ludwig Zenz Cc: Stefano Babic

ARM: imx: dh-imx6: Convert SATA support to DM

2019-06-11T08:42:48Z

Enable DM SATA support on DHCOM iMX6 PDK2. Convert board code to match the DM support. Signed-off-by: Marek Vasut Cc: Fabio Estevam Cc: Ludwig Zenz Cc: Stefano Babic

ARM: imx: dh-imx6: Convert SD/MMC support to DM

2019-06-11T08:42:48Z

Enable DM block and DM MMC support on DHCOM iMX6 PDK2. Convert board code to match the DM support. Signed-off-by: Marek Vasut Cc: Fabio Estevam Cc: Ludwig Zenz Cc: Stefano Babic