u-boot.git/board/exbitgen, branch v2009.01

Align end of bss by 4 bytes

2008-11-18T22:13:16+00:00

Most of the bss initialization loop increments 4 bytes
at a time. And the loop end is checked for an 'equal'
condition. Make the bss end address aligned by 4, so
that the loop will end as expected.

Signed-off-by: Selvamuthukumar 
Signed-off-by: Wolfgang Denk

rename CFG_ macros to CONFIG_SYS

2008-10-18T19:54:03+00:00

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD

rename CFG_ENV macros to CONFIG_ENV

2008-09-10T20:48:06+00:00

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD

rename CFG_ENV_IS_IN_FLASH in CONFIG_ENV_IS_IN_FLASH

2008-09-10T20:48:04+00:00

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD

cleanup use of CFG_ENV_IS_IN_FLASH

2008-09-10T20:48:03+00:00

- #if CFG_ENV_IS_IN_FLASH
- #if (CFG_ENV_IS_IN_FLASH == 1)
- #define CFG_ENV_IS_IN_FLASH 0

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD

rename environment.c in env_embedded.c to reflect is functionality

2008-09-10T20:48:01+00:00

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD

Cleanup: fix "expected specifier-qualifier-list before 'phys_size_t'" errors

2008-07-03T20:34:08+00:00

Signed-off-by: Wolfgang Denk

Cleanup out-or-tree building for some boards (.depend)

2008-07-02T21:49:18+00:00

Signed-off-by: Wolfgang Denk

Change initdram() return type to phys_size_t

2008-06-12T06:50:18+00:00

This patch changes the return type of initdram() from long int to phys_size_t.
This is required for a couple of reasons: long int limits the amount of dram
to 2GB, and u-boot in general is moving over to phys_size_t to represent the
size of physical memory.  phys_size_t is defined as an unsigned long on almost
all current platforms.

This patch *only* changes the return type of the initdram function (in
include/common.h, as well as in each board's implementation of initdram).  It
does not actually modify the code inside the function on any of the platforms;
platforms which wish to support more than 2GB of DRAM will need to modify
their initdram() function code.

Build tested with MAKEALL for ppc, arm, mips, mips-el. Booted on powerpc
MPC8641HPCN.

Signed-off-by: Becky Bruce

ppc4xx: Remove superfluous dram_init() call or replace it by initdram()

2008-06-03T18:22:19+00:00

Historically the 405 U-Boot port had a dram_init() call in early init
stage. This function was still called from start.S and most of the time
coded in assembler. This is not needed anymore (since a long time) and
boards should implement the common initdram() function in C instead.

This patch now removed the dram_init() call from start.S and removes the
empty implementations that are scattered through most of the 405 board
ports. Some older board ports really implement this dram_init() though.
These are:

csb272
csb472
ERIC
EXBITGEN
W7OLMC
W7OLMG

I changed those boards to call this assembler dram_init() function now
from their board specific initdram() instead. This *should* work, but please
test again on those platforms. And it is perhaps a good idea that those
boards use some common 405 SDRAM initialization code from cpu/ppc4xx at
some time. So further patches welcome here.

Signed-off-by: Stefan Roese