u-boot.git/board/freescale/common, branch v2011.09

Minor coding style cleanup.

2011-05-19T20:22:44Z

Signed-off-by: Wolfgang Denk

powerpc/85xx: add support for env in MMC/SPI on corenet ds boards

2011-05-18T14:15:25Z

Signed-off-by: Shaohui Xie Signed-off-by: Kumar Gala

powerpc/fsl: add 'pixis_reset dump' command

2011-04-29T03:09:23Z

Add the 'pixis_reset dump' command, which displays the contents of the PIXIS registers. This command is only available if DEBUG is defined. Signed-off-by: Timur Tabi Signed-off-by: Kumar Gala

powerpc: Add P3041DS/P5020DS board support (uses corenet_ds code)

2011-04-28T03:29:04Z

The P3041DS & P5020DS boards are almost identical (except for the processor in them). Additionally they are based on the P4080DS board design so we use the some board code for all 3 boards. Some ngPIXIS (FPGA) registers where reserved on P4080DS and now have meaning on P3041DS/P5020DS. We utilize some of these for SERDES clock configuration. Additionally, the P3041DS/P5020DS support NAND. Signed-off-by: Timur Tabi Signed-off-by: Shaohui Xie Signed-off-by: Kumar Gala

powerpc/85xx: Enable eSDHC boot support on P2020 DS

2011-04-05T03:26:32Z

We implement our own mmc_get_env_addr since the environment variables are written to just after the u-boot image on SDCard, so we must read the MBR to get the start address and code length of the u-boot image, then calculate the address of the env. Signed-off-by: Jerry Huang Signed-off-by: Zhao Chenhui Signed-off-by: Kumar Gala

fsl: obsolete NXID v0 EEPROMs, automatically upgrade them to NXID v1

2011-04-04T14:24:42Z

The NXID EEPROM format comes in two versions, v0 and v1. The only difference is in the number of MAC addresses that can be stored. NXID v0 supports eight addresses, and NXID v1 supports 23. Rather than allow a board to choose which version to support, NXID v0 is now considered deprecated. The EEPROM code is updated to support only NXID v1, but it can still read EEPROMs formatted with v0. In these cases, the EEPROM data is loaded and the CRC is verified, but the data is stored into a v1 data structure. If the EEPROM data is written back, it is written in v1 format. This allows existing v0-formatted EEPROMs to continue providing MAC addresses, but any changes to the data will force an upgrade to the v1 format, while retaining all data. Signed-off-by: Timur Tabi Signed-off-by: Kumar Gala

p1022ds: allow for board-specific ngPIXIS functions

2011-04-04T14:24:40Z

The ngPIXIS is an FPGA used on the reference boards of most Freescale PowerPC SOCs. Although programming the ngPIXIS is mostly standard on all boards that have it, the P1022DS is unique in that the ngPIXIS needs to be programmed in "indirect" mode whenever the video display (DIU) is active. To support indirect mode, and to make it easier to support other quirks on future reference boards, the low-level ngPIXIS functions are all marked as weak, so that board-specific code can override any of them. We take advantage of this feature on the P1022DS, so that we can properly reset the board when the DIU is active. Signed-off-by: Timur Tabi Signed-off-by: Kumar Gala

fsl: update CRC after setting EEPROM identifier

2011-02-10T05:30:39Z

The "mac id" command is used to initialize the EEPROM data to a specific format, but it was not updating the CRC. This didn't cause any real problems, because writing the data to the EEPROM will always update the CRC anyway, but it did result in a bogus CRC warning. Signed-off-by: Timur Tabi Signed-off-by: Kumar Gala

video: move fsl_diu_fb driver to drivers/video

2010-12-01T19:48:13Z

Since the driver is used not only on Freescale boards, we move it to a common place for video drivers as suggested by Wolfgang. The patch also cleans up the top level Makefile. Signed-off-by: Anatolij Gustschin

512x: Cleanup for partial linking and --gc-sections

2010-11-27T22:35:11Z

Signed-off-by: Wolfgang Denk Cc: Anatolij Gustschin Cc: Timur Tabi Acked-by: Stefan Roese