u-boot.git/board/freescale/common, branch v2016.03

qe: move drivers/qe/qe.h to include/fsl_qe.h

2016-02-24T16:51:13Z

As the QE firmware struct is shared with Fman, move the header file out of drivers/qe/. Signed-off-by: Gong Qianyu Reviewed-by: York Sun

Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriq

2016-01-27T20:05:36Z

secure_boot: change error handler for esbc_validate

2016-01-27T16:13:03Z

In case of error while executing esbc_validate command, SNVS transition and issue of reset is required only for secure-boot. If boot mode is non-secure, this is not required. Similarly, esbc_halt command which puts the core in Spin Loop is applicable only for Secure Boot. Signed-off-by: Aneesh Bansal Acked-by: Ruchika Gupta Reviewed-by: York Sun

secure_boot: enable chain of trust for ARM platforms

2016-01-27T16:12:49Z

Chain of Trust is enabled for ARM platforms (LS1021 and LS1043). In board_late_init(), fsl_setenv_chain_of_trust() is called which will perform the following: - If boot mode is non-secure, return (No Change) - If boot mode is secure, set the following environmet variables: bootdelay = 0 (To disable Boot Prompt) bootcmd = CONFIG_CHAIN_BOOT_CMD (Validate and execute Boot script) Signed-off-by: Aneesh Bansal Acked-by: Ruchika Gupta Reviewed-by: York Sun

secure_boot: create function to determine boot mode

2016-01-27T16:12:42Z

A function is created to detrmine if the boot mode is secure or non-secure for differnt SoC's. Signed-off-by: Aneesh Bansal Acked-by: Ruchika Gupta Reviewed-by: York Sun

powerpc/board/t4240rdb: Enable VID support

2016-01-25T20:38:05Z

The fuse status register provides the values from on-chip voltage ID efuses programmed at the factory. These values define the voltage requirements for the chip. u-boot reads FUSESR and translates the values into the appropriate commands to set the voltage output value of an external voltage regulator. Signed-off-by: Ying Zhang Reviewed-by: York Sun

board/freescale/common: Check IR chip mode for VID support

2016-01-25T20:37:03Z

IR chip on all the boards are required to be used in Intel mode to support VID. VDD will not be adjusted if IR chip is used in other modes. Signed-off-by: Ying Zhang Reviewed-by: York Sun

SECURE BOOT: support for validation of dynamic image

2016-01-25T16:24:16Z

Some images to be validated are relocated to a dynamic address at run time. So, these addresses cannot be known befor hand while signing the images and creating the header offline. So, support is required to pass the image address to the validate function as an argument. If an address is provided to the function, the address field in Header is not read and is treated as a reserved field. Signed-off-by: Saksham Jain Signed-off-by: Aneesh Bansal Acked-by: Ruchika Gupta Reviewed-by: York Sun

SECURE BOOT: separate function created for signature

2016-01-25T16:24:16Z

The code for image hash calculation, hash calculation from RSA signature and comparison of hashes has been mobed to a separate function. Signed-off-by: Saksham Jain Signed-off-by: Aneesh Bansal Acked-by: Ruchika Gupta Reviewed-by: York Sun

SECURE BOOT: separate functions for reading keys

2016-01-25T16:24:16Z

Separate functions are created for reading and checking the sanity of Public keys: - read_validate_single_key - read_validate_ie_tbl - read_validate_srk_table Signed-off-by: Saksham Jain Signed-off-by: Aneesh Bansal Acked-by: Ruchika Gupta Reviewed-by: York Sun