u-boot.git/board/freescale/common, branch v2016.05

Fix various typos, scattered over the code.

2016-05-06T01:39:26Z

Spelling corrections for (among other things): * environment * override * variable * ftd (should be "fdt", for flattened device tree) * embedded * FTDI * emulation * controller

armv8/ls2080ardb: Enable VID support

2016-03-29T15:46:24Z

This patch enable VID support for ls2080ardb platform. It uses the common VID driver. Signed-off-by: Rai Harninder Reviewed-by: York Sun

SECURE BOOT: Change fsl_secboot_validate func to pass image addr

2016-03-29T15:46:23Z

Use a pointer to pass image address to fsl_secboot_validate(), instead of using environmental variable "img_addr". Signed-off-by: Aneesh Bansal Signed-off-by: Saksham Jain Reviewed-by: York Sun

SECURE BOOT: Halt execution when secure boot fail

2016-03-29T15:46:23Z

In case of fatal failure during secure boot execution (e.g. header not found), reset is asserted to stop execution. If the RESET_REQ is not tied to HRESET, this allows the execution to continue. Add esbh_halt() after the reset to make sure execution stops. Signed-off-by: Aneesh Bansal Signed-off-by: Saksham Jain Reviewed-by: York Sun

armv8: fsl-lsch3: Add new header for secure boot

2016-03-29T15:46:20Z

For secure boot, a header is used to identify key table, signature and image address. A new header structure is added for lsch3. Currently key extension (IE) feature is not supported. Single key feature is not supported. Keys must be in table format. Hence, SRK (key table) must be present. Max key number has increase from 4 to 8. The 8th key is irrevocable. A new barker Code is used. Signed-off-by: Aneesh Bansal Signed-off-by: Saksham Jain Reviewed-by: York Sun

freescale: vid: Return i2c mux to default channel

2016-03-21T19:42:15Z

IR chip is on one of the channels on multiplexed I2C-bus. Reset to default channel after accessing. Signed-off-by: Wenbin Song Reviewed-by: York Sun

qe: move drivers/qe/qe.h to include/fsl_qe.h

2016-02-24T16:51:13Z

As the QE firmware struct is shared with Fman, move the header file out of drivers/qe/. Signed-off-by: Gong Qianyu Reviewed-by: York Sun

Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriq

2016-01-27T20:05:36Z

secure_boot: change error handler for esbc_validate

2016-01-27T16:13:03Z

In case of error while executing esbc_validate command, SNVS transition and issue of reset is required only for secure-boot. If boot mode is non-secure, this is not required. Similarly, esbc_halt command which puts the core in Spin Loop is applicable only for Secure Boot. Signed-off-by: Aneesh Bansal Acked-by: Ruchika Gupta Reviewed-by: York Sun

secure_boot: enable chain of trust for ARM platforms

2016-01-27T16:12:49Z

Chain of Trust is enabled for ARM platforms (LS1021 and LS1043). In board_late_init(), fsl_setenv_chain_of_trust() is called which will perform the following: - If boot mode is non-secure, return (No Change) - If boot mode is secure, set the following environmet variables: bootdelay = 0 (To disable Boot Prompt) bootcmd = CONFIG_CHAIN_BOOT_CMD (Validate and execute Boot script) Signed-off-by: Aneesh Bansal Acked-by: Ruchika Gupta Reviewed-by: York Sun