u-boot.git/board/freescale/common, branch v2016.07

board: freescale: common: Add flag for LBMAP brdcfg reg offset

2016-06-03T21:12:51Z

Add QIXIS_LBMAP_BRDCFG_REG to the save offset of LBMAP configuration register instead of hardcoding it in set_lbmap() function. Signed-off-by: Calvin Johnson Signed-off-by: Abhimanyu Saini Signed-off-by: Prabhakar Kushwaha Reviewed-by: York Sun

board: freescale: common: Conditionally compile IFC QXIS func

2016-06-03T21:12:50Z

Check if qixis supports memory-mapped read/write before compiling IFC based qixis read/write functions. Signed-off-by: Calvin Johnson Signed-off-by: Abhimanyu Saini Signed-off-by: Prabhakar Kushwaha Reviewed-by: York Sun

board: ls102xa: Fix ICID setup

2016-06-03T21:12:06Z

LS102A ref manual dictates that ICID have to be written to the MSB of the ICID register, not to the LSB. Signed-off-by: Vincent Siles

arm: uniform usage of u32 in ls102x caam config

2016-05-18T15:51:44Z

Mix usage of uint32_t and u32 fixed in favor of u32. Signed-off-by: Vincent Siles Reviewed-by: York Sun

arm: Fix SCFG ICID reg addresses

2016-05-18T15:51:44Z

On the LS102x boards, in order to initialize the ICID values of masters, the dev_stream_id array holds absolute offsets from the base of SCFG. In ls102xa_config_ssmu_stream_id, the base pointer is cast to uint32_t * before adding the offset, leading to an invalid address. Casting it to void * solves the issue. Signed-off-by: Vincent Siles Reviewed-by: York Sun

Fix various typos, scattered over the code.

2016-05-06T01:39:26Z

Spelling corrections for (among other things): * environment * override * variable * ftd (should be "fdt", for flattened device tree) * embedded * FTDI * emulation * controller

armv8/ls2080ardb: Enable VID support

2016-03-29T15:46:24Z

This patch enable VID support for ls2080ardb platform. It uses the common VID driver. Signed-off-by: Rai Harninder Reviewed-by: York Sun

SECURE BOOT: Change fsl_secboot_validate func to pass image addr

2016-03-29T15:46:23Z

Use a pointer to pass image address to fsl_secboot_validate(), instead of using environmental variable "img_addr". Signed-off-by: Aneesh Bansal Signed-off-by: Saksham Jain Reviewed-by: York Sun

SECURE BOOT: Halt execution when secure boot fail

2016-03-29T15:46:23Z

In case of fatal failure during secure boot execution (e.g. header not found), reset is asserted to stop execution. If the RESET_REQ is not tied to HRESET, this allows the execution to continue. Add esbh_halt() after the reset to make sure execution stops. Signed-off-by: Aneesh Bansal Signed-off-by: Saksham Jain Reviewed-by: York Sun

armv8: fsl-lsch3: Add new header for secure boot

2016-03-29T15:46:20Z

For secure boot, a header is used to identify key table, signature and image address. A new header structure is added for lsch3. Currently key extension (IE) feature is not supported. Single key feature is not supported. Keys must be in table format. Hence, SRK (key table) must be present. Max key number has increase from 4 to 8. The 8th key is irrevocable. A new barker Code is used. Signed-off-by: Aneesh Bansal Signed-off-by: Saksham Jain Reviewed-by: York Sun