u-boot.git/board/freescale, branch v2011.03

Merge branch 'master' of git://git.denx.de/u-boot-arm

2011-03-27T19:20:29Z

rename _end to __bss_end__

2011-03-27T17:18:37Z

Currently, _end is used for end of BSS section. We want _end to mean end of u-boot image, so we rename _end to __bss_end__ first. Signed-off-by: Po-Yu Chuang

powerpc/85xx: Fix PCI memory map setup on P1_P2_RDB

2011-03-24T14:46:21Z

Update the PCIe address map to match standard FSL memory map. Additionally, fix the TLBs so the cover the PCIe address space properly so cards plugged in like an e1000 work correctly. Signed-off-by: Prabhakar Kushwaha Signed-off-by: Kumar Gala

powerpc/mpc8572ds: revise board specific timing for dual-rank DIMMs

2011-03-24T14:20:50Z

Tested all possible values for clk_adjust and write_data_delay for dual rank UDIMM and RDIMM to revise the tables. Signed-off-by: York Sun Signed-off-by: Kumar Gala

powerpc/corenet_ds: revise platform dependent parameters

2011-03-05T16:13:50Z

This patch revised clk_adjust and wrlvl_start timings for corenet_ds, based on testing on Virtium VL33B5163F-K9S and Kingston KVR1333D3Q8R9S/4G. Signed-off-by: York Sun Signed-off-by: Kumar Gala

corenet_ds: pick the middle value for all tested timing parameters

2011-03-05T16:13:50Z

For DDR3 controller, the clk_adjust and wrlvl_start are platform-dependent. The best values should be picked up from the middle of all working combinations. This patch updates the table with confirmed values tested on Hynix dual-rank UDIMMs (HMT125U7BFR8C-H9) at 1300MT/s, 1200MT/s, 1000MT/s, 900MT/s, 800MT/s and Kingston quad-rank RDIMMs (KVR1333D3Q8R9S/4G) at 1300MT/s, 1200MT/s, 1000MT/s. Signed-off-by: York Sun

mx31pdk: Make the full boot log visible

2011-02-21T07:30:54Z

Use board_early_init_f so that the full boot log output can be displayed. Signed-off-by: Fabio Estevam

mx31pdk: Use the new relocation scheme

2011-02-21T07:30:54Z

Signed-off-by: Fabio Estevam

fsl: update CRC after setting EEPROM identifier

2011-02-10T05:30:39Z

The "mac id" command is used to initialize the EEPROM data to a specific format, but it was not updating the CRC. This didn't cause any real problems, because writing the data to the EEPROM will always update the CRC anyway, but it did result in a bogus CRC warning. Signed-off-by: Timur Tabi Signed-off-by: Kumar Gala

Add support for Freescale's mx35pdk board.

2011-02-01T23:54:43Z

The patch adds suupport for the Freescale's mx35pdk board (known as well as mx35_3stack). The board boots from the NOR flash. Following devices are supported: - two ethernet devices (FEC and SMC911x on debug board) - I2C - PMIC (MC13892) via I2C interface - UART - NOR flash (64MB) - NAND flash (2GB) - basic access to mc9sdz60 registers via I2C interface Signed-off-by: Stefano Babic