u-boot.git/board/imgtec, branch v2016.11

boston: Introduce support for the MIPS Boston development board

2016-09-21T14:24:36Z

This patch introduces support for building U-Boot to run on the MIPS Boston development board. This is a board built around an FPGA & an Intel EG20T Platform Controller Hub, used largely as part of the development of new CPUs and their software support. It is essentially the successor to the older MIPS Malta board. Signed-off-by: Paul Burton

MIPS: Malta: Enable CM & L2 support

2016-09-21T13:04:04Z

Enable support for the MIPS Coherence Manager & L2 caches on the MIPS Malta board, removing the need for us to attempt to bypass the L2 during boot (which would fail with recent CPUs that expose L2 config via the CM anyway). Signed-off-by: Paul Burton

mips: Add MIPSfpga platform support

2016-09-21T12:55:14Z

MIPSfpga is an FPGA based dev platform. In a nutshell, its a microAptiv cpu core with lots of Xilinx IP blocks The FPGA dev board used is the Nexys4DDR board by Digilent. For more information, check the Readme file in board/imgtec/xilfpga Signed-off-by: Zubair Lutfullah Kakakhel Reviewed-by: Paul Burton Reviewed-by: Daniel Schwierzeck

malta: Allow MIPS64 builds

2016-05-31T07:38:11Z

Both real Malta boards & emulators that mimic Malta (eg. QEMU) can support MIPS64 CPUs. Allow MIPS64 builds of U-Boot for such boards, which enables the user to make use of the whole 64 bit address space. Signed-off-by: Paul Burton

MIPS: Move CONFIG_SYS_TEXT_BASE to Kconfig

2016-05-25T23:34:13Z

Move CONFIG_SYS_TEXT_BASE to Kconfig, and add default values in board Kconfig files matching what was present in their config headers. This will make it cleaner to conditionalise the value for Malta based on 32 vs 64 bit builds. Signed-off-by: Paul Burton

malta: Tidy up UART address selection

2016-05-25T23:34:13Z

The address of the UART differs based upon the system controller because it's actually within the I/O port region, which is in a different location for each system controller. Rather than handling this as 2 UARTs with the correct one selected at runtime, use I/O port accessors for the UART such that access to it gets translated into the I/O port region automatically. Signed-off-by: Paul Burton Reviewed-by: Daniel Schwierzeck

malta: Remove ".set mips32" directive

2016-05-20T23:36:39Z

We always build for a mips32 or higher ISA, so this ".set mips32" directive is redundant. Once MIPSr6 support is added it will become harmful since some instruction encodings change & this directive will cause the older encodings to be incorrectly emitted instead of the appropriate ones for the build. In preparation for supporting MIPSr6, remove this redundant directive. Signed-off-by: Paul Burton

Use correct spelling of "U-Boot"

2016-02-06T11:00:59Z

Correct spelling of "U-Boot" shall be used in all written text (documentation, comments in source files etc.). Signed-off-by: Bin Meng Reviewed-by: Heiko Schocher Reviewed-by: Simon Glass Reviewed-by: Minkyu Kang

malta: Use I/O accessors for SuperI/O controller

2016-02-01T21:13:25Z

Rather than passing the I/O port base address to the Super I/O code, switch it to using outb such that it makes use of the I/O port base address automatically. Drop the extern keyword to satisfy checkpatch whilst here. Signed-off-by: Paul Burton

malta: Set I/O port base early

2016-02-01T21:13:25Z

Set the I/O port base earlier, from board_early_init_f, in preparation for it being used by the serial driver. Signed-off-by: Paul Burton