u-boot.git/board/keymile/common, branch v2011.06

km/common: implement boardId HWkey checks as u-boot cmd

2011-05-18T21:02:55Z

BoardId and HWKey are used to identify the HW class of a given board. The correct values are stored in the inventory eeprom. During creation time of a boot package the boardId and HWkey for the SW is stored in the default environment and burned into the flash. During boottime the values in the inventory and in the environment are compared to avoid starting of a SW which is not authorized for this board. Some bootpackages are allowed to run on a set of different boardId hwKey. In this case the environment variable boardIdListHex was added to the default environment. In this case the command iterates over the pair values and compares them with the values read from the inventory eeprom. The syntax of such a boardIdListHex value is e.g.: 158_1 159_1 159_2 Signed-off-by: Thomas Herzmann Signed-off-by: Holger Brunck Signed-off-by: Valentin Longchamp Acked-by: Heiko Schocher cc: Wolfgang Denk cc: Detlev Zundel

km/common: implement setboardid command

2011-05-10T21:19:43Z

Read out board id and HW key from the IVM eeprom and set these values as an environment variable. Signed-off-by: Holger Brunck Acked-by: Heiko Schocher cc: Wolfgang Denk cc: Detlev Zundel cc: Valentin Longchamp

powerpc/km82xx: add mgcoge3ne and remove mgcoge2ne support

2011-05-10T20:48:50Z

This patch adds support for the MPC8247 based board mgcoge3ne. Additionaly mgcoge2ne board supprot was removed, because due to the mgcoge3ne, this board is obsolete and not longer maintained. The board is similar to mgcoge. The difference is that a NUMONYX flash is used and a different SDRAM (256MB). Also introduce CONFIG_KM_82XX to collect ppc82xx common settings and remove staticness from the common set_pin function. Signed-off-by: Holger Brunck Signed-off-by: Valentin Longchamp Acked-by: Heiko Schocher cc: Wolfgang Denk cc: Detlev Zundel

powerpc/km82xx: rework DIP switch detection

2011-05-10T20:48:45Z

Introduce a struct for the BFTICU FPGA to increase the readability of the code. And the define CONFIG_SYS_BFTICU_BASE was removed because the CONFIG_SYS_FPGA_BASE is already the base value for BFTICU registers. Signed-off-by: Andreas Huber Signed-off-by: Holger Brunck Signed-off-by: Valentin Longchamp Acked-by: Heiko Schocher cc: Wolfgang Denk cc: Detlev Zundel

km/common: remove hdlc_enet implementation

2011-05-10T20:48:31Z

The hdlc implementation for mgcoge was initially developed, but later on not used. Remove the C files, the references in mgcoge.c and the Makefile to decrease maintenance effort. Signed-off-by: Holger Brunck Acked-by: Heiko Schocher cc: Wolfgang Denk cc: Detlev Zundel cc: Valentin Longchamp Signed-off-by: Valentin Longchamp

keymile, common: add setting of some environment variables

2011-04-29T22:45:22Z

This patch adds last_stage_init to all keymile boards. And in the last stage init some environment variables for u-boot were set. Currently these are pnvramaddr, pram and var address. Signed-off-by: Holger Brunck Signed-off-by: Heiko Schocher Acked-by: Kim Phillips cc: Valentin Longchamp cc: Wolfgang Denk cc: Kim Phillips

keymile boards: add CONFIG_PIGGY_MAC_ADRESS_OFFSET

2011-04-29T22:45:17Z

Normaly the PIGGY_MAC_ADRESS can be read directly from the IVM on keymile boards. On mgcoge3 it differs. Because there are two piggy boards deployed the second MAC adress must be calculated with the IVM mac adress and an offset. This patch allows to set such a offset in the board config. Signed-off-by: Holger Brunck cc: Valentin Longchamp cc: Heiko Schocher

keymile, common; fix i2c deblocking support

2011-04-29T22:45:09Z

This patch fix the i2c deblocking facility with the i2c HW-Controller. The required delays for byte reading, the enhanced criteria for stop the dummy read and required 5 start/stop sequences are added. Add i2c deblocking before ivm eeprom read. Improve i2c deblocking sequence by respecting stop hold time. Cleaned function for deblocking. Have now one function i2c_make_abort() available for bitbang, mpc82xx and mpc83xx harware controller. Signed-off-by: Stefan Bigler Signed-off-by: Holger Brunck Signed-off-by: Heiko Schocher cc: Valentin Longchamp

ppc, 8321: cleanup tuxa1, tuda1 and suvd3 support

2011-04-29T22:45:07Z

For the kmsupx5 a new header file was introduced km8321-common.h. Now the common stuff from tuxa1, tuda1 and suvd3 was removed and the new header file included. The defines CONFIG_SYS_PIGGY_BASE and CONFIG_SYS_PIGGY_SIZE are confusing. Because they actually describe the KMBEC FPGA values. The KMBEC FPGA can be PRIO on kmeter1 or upio on mgcoge. Therefore all the defines were renamed. remove unneeded variable CONFIG_KM_DEF_NETDEV, as it is already declared in keymile-common.h Signed-off-by: Holger Brunck Signed-off-by: Heiko Schocher Acked-by: Kim Phillips cc: Kim Phillips cc: Wolfgang Denk cc: Valentin Longchamp

ppc: add support for ppc based board mgcoge2ne

2011-04-29T22:44:47Z

The mgcoge2 board from keymile deploys two different processors. An ARM based Kirkwood for the "unit" part of the SW and a PPC for the "ne" part of the SW. Therefore in Linux and U-Boot the names for the board are mgcoge2un and mgcoge2ne. This patch adds the mgcoge2ne part of the board. The ppc part of mgboge2 is quite similar to mgcoge, therefore a generic header km82xx-common.h was introduced to collect all similiarities. Currently the only difference is that mgcoge2ne has a 64 MB numonyx NOR flash with a single die. The mgcoge has a dual die flash 2*32MB from spansion. Signed-off-by: Holger Brunck Signed-off-by: Heiko Schocher cc: Wolfgang Denk cc: Valentin Longchamp