u-boot.git/board/keymile, branch v2009.08

83xx, kmeter1, fix: update in the DTS the correct size for the first flash

2009-07-29T23:46:23Z

When updating the "reg" in the "/localbus/flash@f0000000,0" node size was wrong updated for the first flash, because the total size was filled in, instead of the right size for it. Signed-off-by: Heiko Schocher Signed-off-by: Kim Phillips

i2c, mpc83xx: add CONFIG_SYS_I2C_INIT_BOARD for fsl_i2c

2009-07-21T05:06:26Z

This patch adds the possibility to call a board specific i2c bus reset routine for the fsl_i2c bus driver, and adds this option for the keymile kmeter1 board. The deblock sequence for this board is implemented and tested in the following way: CR = 0x20 (release SDA and SCL pin) CR = 0xa0 (start read) dummy read dummy read if 2. dummy read == 0x00 3. dummy read CR = 0x80 (SDA and SCL now 1 SR = 0x86) CR = 0x00 (Modul reset SR=0x81) CR = 0x80 (SDA and SCL = 1, SR = 0x81) Signed-off-by: Heiko Schocher

powerpc: updates for the keymile boards

2009-07-20T22:06:11Z

- CONFIG_SYS_MAX_I2C_BUS changed to 1 We use only one I2C hardwarecontroller on this boards, so change the CONFIG_SYS_MAX_I2C_BUS to 1. - common: dont print errormsg if second IVM Block lacks. - 82xx, mgcoge: fix double mtdpart entry in environment - 82xx, mgcoge: activate on second Flash the second bank. - common: CONFIG_ENV_SIZE 0x4000 for all keymile boards - common: Change malloc size to 1MByte for all Keymile boards We need a bigger malloc area for the environment support (128k) on some Keymile boards (kmeter1) and the upcoming UBI support. Change it to 1MB for all Keymile boards to be on the save side. Also define CONFIG_SYS_64BIT_VSPRINTF which is needed for UBI/UBIFS support. - Add UBI support to all Keymile boards - change manner of writing "/localbus/ranges" node instead of writting the complete "/localbus/ranges" node before booting Linux, only update the ranges entries which gets dynamical detected (size of flashes). This is needed, because keymile adds in the DTS "/localbus/ranges" node entries, which u-boot must not overwrite/delete. - kmeter, mgcoge: define 2 seperate regions needed for the Intel P30 chips The Intel P30 chip has 2 non-identical chips on one die, so we need to define 2 seperate regions that are scanned by physmap_of independantly. - kmeter1: Add MTD concat support to Keymile boards - 82xx, mgcoge: add "unlock=yes" to default environment - added CONFIG_MTD_DEVICE to get in sync with mainline code Signed-off-by: Heiko Schocher Signed-off-by: Stefan Roese

83xx: Replace CONFIG_ECC_INIT_VIA_DDRC references

2009-07-02T16:15:49Z

Update 83xx architecture's CONFIG_ECC_INIT_VIA_DDRC references to CONFIG_ECC_INIT_VIA_DDRCONTROLLER, which other Freescale architectures use Signed-off-by: Peter Tyser Acked-by: Kim Phillips Signed-off-by: Kumar Gala

General help message cleanup

2009-06-12T18:47:16Z

Many of the help messages were not really helpful; for example, many commands that take no arguments would not print a correct synopsis line, but "No additional help available." which is not exactly wrong, but not helpful either. Commit ``Make "usage" messages more helpful.'' changed this partially. But it also became clear that lots of "Usage" and "Help" messages (fields "usage" and "help" in struct cmd_tbl_s respective) were actually redundant. This patch cleans this up - for example: Before: => help dtt dtt - Digital Thermometer and Thermostat Usage: dtt - Read temperature from digital thermometer and thermostat. After: => help dtt dtt - Read temperature from Digital Thermometer and Thermostat Usage: dtt Signed-off-by: Wolfgang Denk

boards: get mac address from environment

2009-03-20T21:39:10Z

The boards that get converted here to use the environment for the mac address rather than global data: debris mgcoge mgsuvd muas3001 netstal pn62 sixnet vcma9 xilinx (the ones that use xilinx_enet) Signed-off-by: Mike Frysinger CC: Ben Warren CC: Sangmoon Kim CC: Heiko Schocher CC: David Mueller CC: Niklaus Giger CC: Wolfgang Grandegger CC: Dave Ellis CC: Ricardo Ribalda

8xx: add support for new keymile kmsupx4 board.

2009-03-18T19:50:05Z

This patch adds support for the kmsupx4 board from Keymile, based on a Freescale MPC852T CPU - serial console on SMC1 - 32 MB SDRAM - 32 MB NOR Flash - Ethernet over SCC3 - I2C Bitbang Signed-off-by: Heiko Schocher

8xx, mgsuvd: rename board to a more generic name

2009-03-18T19:50:04Z

renaming the "mgsuvd" board port into "km8xx", because there come more similar boards from keymile. Compiling the mgsuvd board with "make mgsuvd_config" remains. Signed-off-by: Heiko Schocher

83xx, kmeter: QE_ENET10 errata for Silicon Revision 2.1

2009-03-06T00:21:29Z

old code implemented the QE_ENET10 errata only for Silicon Revision 2.0. New code reads now the Silicon Revision register and sets dependend on the Silicon Revision the values as advised in the QE_ENET10 errata. Signed-off-by: Heiko Schocher Signed-off-by: Kim Phillips

83xx, kmeter1: autodetect size of DDR II RAM

2009-03-06T00:21:17Z

it is possible that some board variants have different DDR II RAM sizes. So we autodetect the size of the assembled RAM. Signed-off-by: Heiko Schocher Signed-off-by: Kim Phillips