u-boot.git/board/keymile, branch v2016.01

km/powerpc: fix ft_board_setup prototype for km82xx & km83xx

2015-11-18T20:28:58Z

Signed-off-by: Valentin Longchamp

powerpc/83xx: add support for kmtegr1 board

2015-11-18T20:28:58Z

This board uses the same CPU (8309) as VECT1. The memory however is different since it has NAND Flash, the NOR Flash partitioning is different and of course the FPGAs as well. Signed-off-by: Valentin Longchamp Signed-off-by: Christoph Dietrich

board/keymile/km82xx: setting dip_switch 3 and 4 will run bootloader

2015-11-18T20:28:56Z

Setting dip_switch 3 and 4 also will run bootloader in COGE3 and COGE6 It is required remove local mgmt IP address, when DIP Switch PIN3 is enabled. DIP Switch 4 also enabled to avoid u-boot update in future for DIP switch enhancements. Signed-off-by: Bagavathiannan Palanisamy Signed-off-by: Valentin Longchamp

km/powerpc82xx: remove unused function

2015-11-18T20:28:55Z

commit 0a4f88b98 removed the usage of our setports function, but the function itself were not removed. So toss it it's dead code. Signed-off-by: Holger Brunck Signed-off-by: Valentin Longchamp

km/powerpc: remove unneeded defines

2015-11-18T20:28:54Z

We use CONFIG_OF_LIBFDT and CONFIG_OF_BOARD_SETUP on all our powerpc targets, so there is no need to check these defines within our C code. Signed-off-by: Holger Brunck Signed-off-by: Valentin Longchamp

powerpc/82xx/km: add testpin detection for mgcoge3ne

2015-11-18T20:28:53Z

On mgcoge3ne we also want to start the test application if the testpin is asserted. But we don't have a full POST test support yet. So simply add a function to read the testpin value. Signed-off-by: Holger Brunck Signed-off-by: Valentin Longchamp

powerpc/82xx: make set/get_pin for km82xx more flexible

2015-11-18T20:28:52Z

The get_pin and set_pin funciton was only used for pins on Port D and therefore the value was hard coded in the function. Enhance this with a parameter, that we are able to use this functions for other ports too. Signed-off-by: Holger Brunck Signed-off-by: Valentin Longchamp

powerpc/83xx: add support for kmtepr2 board

2015-11-18T20:28:51Z

This board is similar to TUXX1, but it has differend FPGAs. Signed-off-by: Christoph Dietrich Signed-off-by: Andreas Huber Signed-off-by: Valentin Longchamp

km/scripts: search for kernel/DTBs at serverip:/PRODUCTNAME via TFTP in develop mode

2015-11-18T20:28:51Z

Search for the kernel and DTBs in a folder named PRODUCTNAME (found in the IVM) at the TFTP server instead of the u-boot boardname. Signed-off-by: Tobias Müller Signed-off-by: Valentin Longchamp Reviewed-by: Heiko Schocher

km/scripts: load fdt_bid_kwkey.dtb when working with tftp

2015-11-18T20:28:50Z

When loading the dtb file via tftp we should load the one which matches boardId and hwKey and not a common one for the boardname. We have boards were different hwKeys are used and then we may load an incorrect dtb file. If no fdt_bid_kwkey.dtb file is not a fallback to boardname.dtb is used. Signed-off-by: Holger Brunck Signed-off-by: Tobias Müller Signed-off-by: Valentin Longchamp Reviewed-by: Heiko Schocher