u-boot.git/board/logicpd/zoom2, branch master

TI:omap3: Drop omap3_zoom2

2014-01-07T21:41:12Z

The omap3_zoom2 board has not been updated for a correct CONFIG_SYS_HZ and Tom Rix's email has long been bouncing. Signed-off-by: Tom Rini

board: arm: convert makefiles to Kbuild style

2013-11-01T15:42:12Z

Signed-off-by: Masahiro Yamada Cc: Albert ARIBAUD Cc: Andreas Bießmann Cc: Stefano Babic Cc: Prafulla Wadaskar Cc: Minkyu Kang Cc: Vipin Kumar Cc: Tom Warren Cc: Tom Rini

Add GPL-2.0+ SPDX-License-Identifier to source files

2013-07-24T13:44:38Z

Signed-off-by: Wolfgang Denk [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini

omap_hsmmc: add driver check for write protection

2013-03-08T21:41:13Z

Add check for write protection in omap mmc driver. Signed-off-by: Nikita Kiryanov Signed-off-by: Igor Grinberg Reviewed-by: Tom Rini

omap_hsmmc: implement driver check for card detection

2013-03-08T21:41:13Z

Implement driver check for card detection. Signed-off-by: Nikita Kiryanov Signed-off-by: Igor Grinberg

serial: zoom2: Remove zoom2 serial prototypes from serial.h

2012-10-15T18:53:50Z

Remove the prototypes for zoom2_serial_deviceN from serial.h . This can't be done right away, as they are referenced from the zoom2 config file. Therefore, adjust the code so the config file only specifies number of the port. Then, replace the simple return in default_serial_console() with a switch across possible values, which returns the zoom2_serial_deviceN . With such adjustment in place, the exported prototypes in serial.h can be safely removed. Signed-off-by: Marek Vasut Cc: Marek Vasut Cc: Tom Rini

serial: Properly spell out the structure member names of serial_driver

2012-10-15T18:53:48Z

Properly spell out the whole structure member names when an initialized varible is instantiated from the struct serial_driver. In case the structure definition for struct serial_driver undergoes reordering, there will be no impact on variables defined based on this structure. Signed-off-by: Marek Vasut Cc: Marek Vasut Cc: Tom Rini Cc: Anatolij Gustschin Cc: Stefan Roese Cc: Mike Frysinger Cc: C Nauman Cc: Minkyu Kang Cc: Michal Simek

COMMON: Use __stringify() instead of rest of implementations

2012-10-15T18:53:47Z

Fix up the rest of implementations of __stringify(). Signed-off-by: Marek Vasut Cc: Wolfgang Denk

ARM:OMAP+:MMC: Add parameters to MMC init

2012-05-15T06:31:22Z

Add parameters to the OMAP MMC initialization function so the board can mask host capabilities and set the maximum clock frequency. While the OMAP supports a certain set of MMC host capabilities, individual boards may be more restricted and the OMAP may need to be configured to match the board. The PRG_SDMMC1_SPEEDCTRL bit in the OMAP3 is an example. Signed-off-by: Jonathan Solnit

omap: Don't use gpio_free to change direction to input

2011-10-27T19:56:35Z

gpio_free() should not have the side effect of setting the line to input since this prevents the gpio command from being able to set a line as output. Signed-off-by: Joe Hershberger Cc: Joe Hershberger Cc: Sandeep Paulraj Signed-off-by: Sandeep Paulraj