u-boot.git/board/mpc8540eval, branch v1.3.2

Remove erroneous or extra spd.h #includers.

2008-03-04T23:17:43+00:00

Many of the spd.h #includers don't need it,
and wanted to have spd_sdram() declared instead.
Since they didn't get that, some also had open
coded extern declarations of it instead or as well.
Fix it all up by using spd_sdram.h where needed.

Signed-off-by: Jon Loeliger

85xx: Convert MPC8540EVAL to new TLB setup

2008-01-17T08:09:20+00:00

Signed-off-by: Kumar Gala

85xx: Use proper defines for PCI addresses

2008-01-17T05:21:56+00:00

We should be using the _MEM_PHYS for LAW and TLB setup and not _MEM_BASE.
While _MEM_BASE & _MEM_PHYS are normally the same, _MEM_BASE should only
be used for configuring the PCI ATMU.

Signed-off-by: Kumar Gala

85xx: convert remaining 85xx boards over to use new LAW init code

2008-01-17T05:21:56+00:00

Converted ATUM8548, MPC8568 MDS, MPC8540 EVAL, and TQM85xx boards over
to use new LAW init code.

Signed-off-by: Kumar Gala

Fix linker scripts: add NOLOAD atribute to .bss/.sbss sections

2008-01-12T19:31:39+00:00

With recent toolchain versions, some boards would not build because
or errors like this one (here for ocotea board when building with
ELDK 4.2 beta):
ppc_4xx-ld: section .bootpg [fffff000 -> fffff23b] overlaps section .bss [fffee900 -> fffff8ab]

For many boards, the .bss section is big enough that it wraps around
at the end of the address space (0xFFFFFFFF), so the problem will not
be visible unless you use a 64 bit tool chain for development. On
some boards however, changes to the code size (due to different
optimizations) we bail out with section overlaps like above.

The fix is to add the NOLOAD attribute to the .bss and .sbss
sections, telling the linker that .bss does not consume any space in
the image.

Signed-off-by: Wolfgang Denk

Reworked FSL Book-E TLB macros to be more readable

2008-01-09T22:25:03+00:00

The old macros made it difficult to know what WIMGE and perm bits
were set for a TLB entry.  Actually use the bit masks for these items
since they are only a single bit.

Also moved the macros into mmu.h out of e500.h since they aren't specific
to e500.

Signed-off-by: Kumar Gala

Stop using immap_t on 85xx

2007-12-12T04:34:20+00:00

In the future the offsets to various blocks may not be in same location.
Move to using CFG_MPC85xx_*_ADDR as the base of the registers
instead of getting it via &immap.

Signed-off-by: Kumar Gala

Stop using immap_t for guts offset on 85xx

2007-12-12T04:34:19+00:00

In the future the offsets to various blocks may not be in same location.
Move to using CFG_MPC85xx_GUTS_ADDR as the base of the guts registers
instead of getting it via &immap->im_gur.

Signed-off-by: Kumar Gala

Move "ar" flags to config.mk to allow for silent "make -s"

2006-10-08T23:02:05+00:00

Based on patch by Mike Frysinger, 20 Jun 2006

Add support for a saving build objects in a separate directory.

2006-09-01T17:49:50+00:00

Modifications are based on the linux kernel approach and
support two use cases:

  1) Add O= to the make command line
  'make O=/tmp/build all'

  2) Set environement variable BUILD_DIR to point to the desired location
  'export BUILD_DIR=/tmp/build'
  'make'

The second approach can also be used with a MAKEALL script
'export BUILD_DIR=/tmp/build'
'./MAKEALL'

Command line 'O=' setting overrides BUILD_DIR environent variable.

When none of the above methods is used the local build is performed and
the object files are placed in the source directory.