u-boot.git/board/nvidia/harmony, branch v2014.04

board: arm: convert makefiles to Kbuild style

2013-11-01T15:42:12Z

Signed-off-by: Masahiro Yamada Cc: Albert ARIBAUD Cc: Andreas Bießmann Cc: Stefano Babic Cc: Prafulla Wadaskar Cc: Minkyu Kang Cc: Vipin Kumar Cc: Tom Warren Cc: Tom Rini

Add GPL-2.0+ SPDX-License-Identifier to source files

2013-07-24T13:44:38Z

Signed-off-by: Wolfgang Denk [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini

ARM: tegra: enable LCD panel on Harmony

2013-07-11T21:15:16Z

Signed-off-by: Stephen Warren Signed-off-by: Tom Warren

Tegra: MMC: Add DT support to MMC driver for all T20 boards

2013-03-14T18:06:42Z

tegra_mmc_init() now parses the DT info for bus width, WP/CD GPIOs, etc. Tested on Seaboard, fully functional. Tamonten boards (medcom-wide, plutux, and tec) use a different/new dtsi file w/common settings. Signed-off-by: Tom Warren Signed-off-by: Thierry Reding Reviewed-by: Stephen Warren

ARM: tegra: enable 8-bit SD slots in board files

2012-11-19T15:15:42Z

Harmony contains an SD slot with all 8 bits routed. This allows plugging in an eMMC-chip-in-SD-form-factor. Seaboard/Springbank/Ventana/AC100 all have an eMMC chip with all 8 bits hooked up. Now that the U-Boot eMMC code fully supports 8-bit operation, initialize those ports as 8-bit instead of 4-bit to improve performance. Whistler was already registering its ports as 8-bit. TrimSlice doesn't have any 8-bit ports. I don't have any Avionic Design boards nor the Colibri board to test with. Signed-off-by: Stephen Warren Signed-off-by: Tom Warren

ARM: tegra: Harmony: enable ULPI USB port

2012-10-29T16:07:04Z

The ULPI port is routed onto pins on the mini PCI Express connector. A standard breakout board may be used to access the port. * Add required DT entries to configure the ULPI port. * Setup up the ULPI pinmux in the board code. * Enable multiple USB controller and ULPI support in the board config. Signed-off-by: Stephen Warren Signed-off-by: Tom Warren

tegra20: rework UART GPIO handling

2012-10-15T18:54:07Z

Rename board provided gpio_config_uart() to gpio_early_init_uart() as it does the same thing as the equally called function provided by the uart-switch code. This allows to simply call this function in early board init whether or not we are building with CONFIG_UART_SWITCH defined. Also provide a weak symbol for this function, to avoid the need to provide this function for boards that don't need any fixup. This patch supersedes the earlier posted "tegra: convert gpio_config_uart to weak symbol". Build tested with MAKEALL -s tegra20 Signed-off-by: Lucas Stach Acked-by: Simon Glass Signed-off-by: Tom Warren

Tegra20: Move some include files to arch-tegra for sharing with Tegra30

2012-10-15T18:54:06Z

The move is pretty straight-forward. ap20.h and tegra20.h were renamed to ap.h and tegra.h. Some files remain in arch-tegra20 but 'include' a file in 'arch-tegra' with #defines & structs that will be common between T20 and T30 HW. HW-specific #defines, etc. stay in the 'arch-tegra20' 'root' file. All boards build OK w/MAKEALL -s tegra20. Checkpatch.pl runs clean. Seaboard works OK. Signed-off-by: Tom Warren

Tegra: Change Tegra20 to Tegra in common code, prep for T30

2012-09-10T20:01:24Z

Convert TEGRA20_ defines to either TEGRA_ or NV_PA_ where appropriate. Convert tegra20_ source file and function names to tegra_, also. Upcoming Tegra30 port will use common code/defines/names where possible. Signed-off-by: Tom Warren Acked-by: Stephen Warren

ARM: tegra: remove redundant mkdirs from board Makefiles

2012-09-07T20:54:31Z

None of harmony, seaboard, ventana, whistler directly build files from ../common/, so there's no need to mkdir the obj directory for such files. Signed-off-by: Stephen Warren Signed-off-by: Tom Warren