u-boot.git/board/nvidia/seaboard, branch v2013.01

ARM: tegra: enable 8-bit SD slots in board files

2012-11-19T15:15:42Z

Harmony contains an SD slot with all 8 bits routed. This allows plugging in an eMMC-chip-in-SD-form-factor. Seaboard/Springbank/Ventana/AC100 all have an eMMC chip with all 8 bits hooked up. Now that the U-Boot eMMC code fully supports 8-bit operation, initialize those ports as 8-bit instead of 4-bit to improve performance. Whistler was already registering its ports as 8-bit. TrimSlice doesn't have any 8-bit ports. I don't have any Avionic Design boards nor the Colibri board to test with. Signed-off-by: Stephen Warren Signed-off-by: Tom Warren

ARM: tegra: don't request GPIO from Seaboard's SPL

2012-10-29T16:07:05Z

Seaboard has a GPIO that switches an external mux between Tegra's debug UART and SPI flash. This is initialized from the SPL so that SPL debug output can be seen. Simplify the code that does this, and don't actually request the GPIO in the SPL; just program it. This saves ~4.5K from the size of the SPL, mostly BSS due to the large gpio_names[] table that is no longer required. This makes Seaboard's SPL fit within the current max size. Signed-off-by: Stephen Warren Acked-by: Simon Glass Acked-by: Allen Martin Tested-by: Simon Glass Signed-off-by: Tom Warren

ARM: tegra: select between Seaboard/Ventana at compile time

2012-10-29T16:07:05Z

Seaboard and Ventana are very similar boards, and so share the seaboard.c board file. The one difference needed so far is detected at run-time by calling machine_is_ventana(). This bloats the Ventana build with code that is never used. Switch to detecting Ventana at compile time to remove bloat. This shaves ~5K off the SPL size on Ventana, and makes the SPL fit within the max size. Signed-off-by: Stephen Warren Acked-by: Simon Glass Tested-by: Simon Glass Signed-off-by: Tom Warren

tegra20: rework UART GPIO handling

2012-10-15T18:54:07Z

Rename board provided gpio_config_uart() to gpio_early_init_uart() as it does the same thing as the equally called function provided by the uart-switch code. This allows to simply call this function in early board init whether or not we are building with CONFIG_UART_SWITCH defined. Also provide a weak symbol for this function, to avoid the need to provide this function for boards that don't need any fixup. This patch supersedes the earlier posted "tegra: convert gpio_config_uart to weak symbol". Build tested with MAKEALL -s tegra20 Signed-off-by: Lucas Stach Acked-by: Simon Glass Signed-off-by: Tom Warren

Tegra20: Move some include files to arch-tegra for sharing with Tegra30

2012-10-15T18:54:06Z

The move is pretty straight-forward. ap20.h and tegra20.h were renamed to ap.h and tegra.h. Some files remain in arch-tegra20 but 'include' a file in 'arch-tegra' with #defines & structs that will be common between T20 and T30 HW. HW-specific #defines, etc. stay in the 'arch-tegra20' 'root' file. All boards build OK w/MAKEALL -s tegra20. Checkpatch.pl runs clean. Seaboard works OK. Signed-off-by: Tom Warren

Tegra: Change Tegra20 to Tegra in common code, prep for T30

2012-09-10T20:01:24Z

Convert TEGRA20_ defines to either TEGRA_ or NV_PA_ where appropriate. Convert tegra20_ source file and function names to tegra_, also. Upcoming Tegra30 port will use common code/defines/names where possible. Signed-off-by: Tom Warren Acked-by: Stephen Warren

ARM: tegra: remove redundant mkdirs from board Makefiles

2012-09-07T20:54:31Z

None of harmony, seaboard, ventana, whistler directly build files from ../common/, so there's no need to mkdir the obj directory for such files. Signed-off-by: Stephen Warren Signed-off-by: Tom Warren

tegra20: rename tegra2 -> tegra20

2012-09-01T12:58:21Z

This is make naming consistent with the kernel and devicetree and in preparation of pulling out the common tegra20 code. Signed-off-by: Allen Martin Acked-by: Stephen Warren Tested-by: Thierry Reding Signed-off-by: Tom Warren

mmc: tegra2: rename tegra2_mmc.* to tegra_mmc.*

2012-07-07T12:07:20Z

In anticipation of Tegra3 support, continue removing/renaming Tegra2-specific files. No functional changes (yet). Updated copyrights to 2012. Signed-off-by: Tom Warren

tegra: usb: Add USB support to nvidia boards

2012-03-29T06:12:49Z

This adds basic USB support for port 0. The other port is not supported yet. Tegra2 (SeaBoard) # usb start (Re)start USB... USB: Register 10011 NbrPorts 1 USB EHCI 1.00 scanning bus for devices... 5 USB Device(s) found scanning bus for storage devices... 1 Storage Device(s) found Tegra2 (SeaBoard) # ext2load usb 0:3 10000000 /boot/vmlinuz Loading file "/boot/vmlinuz" from usb device 0:3 (ROOT-A) 2932976 bytes read Signed-off-by: Simon Glass Signed-off-by: Tom Warren