u-boot.git/board/nvidia/seaboard, branch v2016.11

ARM: tegra: fix ULPI PHY on Ventana and Seaboard

2016-09-27T16:11:03Z

Commit ce02a71c2374 "tegra: dts: Sync tegra20 device tree files with Linux" enabled the ULPI USB port on Ventana, but made no attempt to ensure that U-Boot code could handle this. In practice, various code is missing, and various configuration options are not enabled, which causes U-Boot to hang when attempting to initialize this USB port. This patch enables ULPI PHY support on Ventana, and adds the required pinmux setup for the port to operate. Note that Ventana is so similar to Seaboard that this change is made in the Seaboard board file, which is shared with Ventana. Seaboard also has the ULPI USB port wired up in hardware, although to an internal port that often doesn't have anything attached to it. However, the DT nodes for the USB controller and PHY had different status property values, so the port was not initialized by U-Boot. Fix this inconsistency, and enable the ULPI port, just like in the Linux kernel DT. This likewise requires enabling ULPI support in the Seaboard defconfig. Cc: Marcel Ziswiler Signed-off-by: Stephen Warren Reviewed-by: Simon Glass Signed-off-by: Tom Warren

ARM: tegra: use DT bindings for GPIO naming

2016-05-31T16:53:56Z

There are currently many places that define the list of all Tegra GPIOs; the DT binding header and custom Tegra-specific header file gpio.h. Fix the redundancy by replacing everything with the DT binding header file. Signed-off-by: Stephen Warren Reviewed-by: Simon Glass Signed-off-by: Tom Warren

tegra: seaboard: Correct the gpio_request() call

2015-03-30T16:59:58Z

Requesting a GPIO without a name is not supposed anymore. This causes the request to fail. Add a name so that the serial console works on seaboard. Signed-off-by: Simon Glass Reported-by: Stephen Warren Signed-off-by: Tom Warren

dm: tegra: Enable driver model in SPL and adjust the GPIO driver

2015-03-04T19:55:04Z

Use the full driver model GPIO and serial drivers in SPL now that these are supported. Since device tree is not available they will use platform data. Remove the special SPL GPIO function as it is no longer needed. This is all in one commit to maintain bisectability. Signed-off-by: Simon Glass

tegra: make local functions static

2014-10-25T11:27:37Z

Signed-off-by: Jeroen Hofstee

kconfig: remove redundant "string" type in arch and board Kconfigs

2014-09-13T20:43:55Z

Now the types of CONFIG_SYS_{ARCH, CPU, SOC, VENDOR, BOARD, CONFIG_NAME} are specified in arch/Kconfig. We can delete the ones in arch and board Kconfig files. This commit can be easily reproduced by the following command: find . -name Kconfig -a ! -path ./arch/Kconfig | xargs sed -i -e ' /config[[:space:]]SYS_$ARCH\|CPU\|SOC\|\VENDOR\|BOARD\|CONFIG_NAME$/ { N s/\n[[:space:]]*string// } ' Signed-off-by: Masahiro Yamada

tegra: Convert tegra GPIO driver to use driver model

2014-09-10T18:59:59Z

This is an implementation of GPIOs for Tegra that uses driver model. It has been tested on trimslice and also using the new iotrace feature. The implementation uses a top-level GPIO device (which has no actual GPIOS). Under this all the banks are created as separate GPIO devices. The GPIOs are named as per the Tegra datasheet/header files: A0..A7, B0..B7, ..., Z0..Z7, AA0..AA7, etc. Since driver model is not yet available before relocation, or in SPL, a special function is provided for seaboard's SPL code. Signed-off-by: Simon Glass

tegra: kconfig: move board select menu and common settings

2014-08-31T01:19:32Z

Becuase the board select menu in arch/arm/Kconfig is too big, move the Tegra board select menu to tegra/Kconfig. Insert the Tegra SoC select menu between the arch select and the board select. Architecture select |-- Tegra Platform (Tegra) |- Tegra SoC select (Tegra20 / 30 / 114 / 124) |- Board select Consolidate also common settings (CONFIG_SYS_CPU="armv7" and CONFIG_SYS_SOC="tegra*") and always "select" CONFIG_SPL as follows: config TEGRA bool select SPL Signed-off-by: Masahiro Yamada Acked-by: Stephen Warren Cc: Tom Warren

Add board MAINTAINERS files

2014-07-30T12:48:06Z

We have switched to Kconfig and the boards.cfg file is going to be removed. We have to retrieve the board status and maintainers information from it. The MAINTAINERS format as in Linux Kernel would be nice because we can crib the scripts/get_maintainer.pl script. After some discussion, we chose to put a MAINTAINERS file under each board directory, not the top-level one because we want to collect relevant information for a board into a single place. TODO: Modify get_maintainer.pl to scan multiple MAINTAINERS files. Signed-off-by: Masahiro Yamada Suggested-by: Tom Rini Acked-by: Simon Glass

kconfig: add board Kconfig and defconfig files

2014-07-30T12:48:01Z

This commit adds: - arch/${ARCH}/Kconfig provide a menu to select target boards - board/${VENDOR}/${BOARD}/Kconfig or board/${BOARD}/Kconfig set CONFIG macros to the appropriate values for each board - configs/${TARGET_BOARD}_defconfig default setting of each board (This commit was automatically generated by a conversion script based on boards.cfg) In Linux Kernel, defconfig files are located under arch/${ARCH}/configs/ directory. It works in Linux Kernel since ARCH is always given from the command line for cross compile. But in U-Boot, ARCH is not given from the command line. Which means we cannot know ARCH until the board configuration is done. That is why all the "*_defconfig" files should be gathered into a single directory ./configs/. Signed-off-by: Masahiro Yamada Acked-by: Simon Glass