u-boot.git/board/nvidia, branch v2012.10

Tegra: Change Tegra20 to Tegra in common code, prep for T30

2012-09-10T20:01:24+00:00

Convert TEGRA20_ defines to either TEGRA_ or NV_PA_ where appropriate.
Convert tegra20_ source file and function names to tegra_, also.

Upcoming Tegra30 port will use common code/defines/names where possible.

Signed-off-by: Tom Warren 
Acked-by: Stephen Warren

ARM: tegra: fix Ventana standalone build

2012-09-07T20:54:32+00:00

Ventana always pulls in files from the Seaboard directory, so needs to
mkdir $(obj)../seaboard unconditionally. This fixes:

git clean -f -d -x
./MAKEALL ventana

"MAKEALL -s tegra20" passes without this change, because Seaboard
happens to be built before Ventana, and hence the directory has already
been created.

I believe the mkdir is only needed for out-of-tree builds, since the
seaboard directory is part of the source tree. However, since we always
build an SPL for Tegra now, which I believe is effectively an out-of-tree
build, we will always need this at some time. The overhead of just
uncondtionally executing the mkdir is minimal, and simplifies the
Makefile, since we don't need to code up the exact minimal condition to
execute the mkdir.

Signed-off-by: Stephen Warren 
Signed-off-by: Tom Warren

ARM: tegra: remove redundant mkdirs from board Makefiles

2012-09-07T20:54:31+00:00

None of harmony, seaboard, ventana, whistler directly build files from
../common/, so there's no need to mkdir the obj directory for such files.

Signed-off-by: Stephen Warren 
Signed-off-by: Tom Warren

tegra: enable NAND on Harmony

2012-09-07T20:54:31+00:00

Signed-off-by: Stephen Warren 
Signed-off-by: Tom Warren

tegra: fdt: Add NAND definitions to fdt

2012-09-07T20:54:30+00:00

Add a flash node to handle the NAND, including memory timings and
page / block size information.

Signed-off-by: Simon Glass 
Signed-off-by: Tom Warren

tegra20: move SDRAM param save to later in boot

2012-09-01T12:58:22+00:00

Move warmboot_save_sdram_params() to later in the boot sequence.  This
code relies on devicetree to get the address of the memory controller
and with upcoming changes for SPL boot it gets called early in the
boot process when devicetree is not initialized yet.

Signed-off-by: Allen Martin 
Acked-by: Stephen Warren 
Tested-by: Thierry Reding 
Signed-off-by: Tom Warren

tegra20: remove timer_init from SPL build

2012-09-01T12:58:21+00:00

Don't use timer_init from tegra board.c.  This comes out of arm720t
for the SPL build.

Signed-off-by: Allen Martin 
Acked-by: Stephen Warren 
Tested-by: Thierry Reding 
Signed-off-by: Tom Warren

tegra20: rename tegra2 -> tegra20

2012-09-01T12:58:21+00:00

This is make naming consistent with the kernel and devicetree and in
preparation of pulling out the common tegra20 code.

Signed-off-by: Allen Martin 
Acked-by: Stephen Warren 
Tested-by: Thierry Reding 
Signed-off-by: Tom Warren

tegra: add pin_mux_spi() board initialization function

2012-07-09T20:44:33+00:00

Boards can override this to set up the pinmux correctly to access serial
flash.

Signed-off-by: Stephen Warren 
Signed-off-by: Tom Warren

tegra: fix leftover CONFIG_TEGRA2_MMC & _SPI build switches

2012-07-09T20:44:32+00:00

Missed some boards after my tegra2_mmc.* -> tegra_mmc.* change, and
one instance of CONFIG_TEGRA2_SPI. MAKEALL -s tegra2 AOK, Seaboard MMC
AOK. Didn't test Tamonten, Paz00 or TrimSlice, as I have none here.

Signed-off-by: Tom Warren 
Acked-by: Stephen Warren